Maxcess MAGPOWR DTR-65 Скачать руководство пользователя страница 30

Страница: 30 / 45

4–11

OPERATION

www.maxcessintl.com

MAGPOWR DTR-65

MI 850A349 1 D

Tension calibration
errors

Display

Error description

PASS

Calibration was successful. No Errors found.

Er 1

Signal read by the amplifier is too large when maximum tension is applied.
This is caused by maximum tension being too large. Reduce maximum
tension.

Er 2

Signal read by the amplifier is too small. Too little of the load cell range is
being used, thus the gain is greater than 32:1. Use more of the load cell
range or set maximum tension higher.

Er 3

Roller weight too large. Roller weight exceeds 90% of the load cell rating.
Make roller weight smaller.

Er 4

Calibration tension is greater than Maximum tension. Make Maximum
tension larger than Calibration tension.

Er 5

Maximum tension exceeds the load cell rating. Lower wrap angle, make
roll weight smaller or get higher rated load cells.

Table 4. Load cell calibration errors.

Содержание MAGPOWR DTR-65














































Результаты поиска

Содержание MAGPOWR DTR-65

Отзывы:

Похожие инструкции для MAGPOWR DTR-65

Бренды по названию

Популярные бренды

Maxcess MAGPOWR DTR-65, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MAGPOWR DTR-65

Отзывы:

Похожие инструкции для MAGPOWR DTR-65

Бренды по названию

Популярные бренды