Maxcess MAGPOWR DTR-65 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 45

background image

3–1

INSTALLATION

www.maxcessintl.com

MAGPOWR DTR-65

MI 850A349 1 D

Mechanical
installation

WARNING – Death or injury can result from unexpected
movement of the machine into which the DTR-65 is installed.

Protect against unexpected movement by removing electrical
power from the digital load cell amplifier and the machine
into which the digital load cell amplifier is installed.

WARNING – Danger of injury from crushing.

Maintenance and repair tasks on the digital load cell
amplifier must be performed only when the machine into
which the DTR-65 is installed has been stopped and has
been secured from being turned on again.

WARNING – Shock may result from water or conductive
particles entering the DTR-65 enclosure due to poor gasket
sealing on the front panel.

To maintain the IP65 rating on the front panel, be sure the
gasket is properly seated between the DTR-65 front panel
and the panel into which the DTR-65 is installed.

«
...
9
10
11
12
13
...
»

Содержание MAGPOWR DTR-65














































Отзывы:

Нет отзывов

Похожие инструкции для MAGPOWR DTR-65

Бренд: Monacor Страницы: 20

Бренд: SKP Pro Audio Страницы: 12

Бренд: GOODWOOD AUDIO Страницы: 4

Бренд: Eagletone Страницы: 3

Бренд: GLEMM Страницы: 12

Cat-5 Computer Video Receiver DA1921SX

Бренд: Altinex Страницы: 9

Бренд: Powerwave Technologies Страницы: 20

IMX18-DI03-4S-5R-S Series

Бренд: turck Страницы: 8

GTR-7535/104/102

Бренд: JBL Страницы: 38

Бренд: McIntosh Страницы: 36

Бренд: VINTAGE SOUND AMPS Страницы: 9

Бренд: Milestone Страницы: 16

Бренд: StetSom Страницы: 40

Бренд: B&K Страницы: 16

Power Drive DNA-2

Бренд: McCormack Страницы: 4

Бренд: E&I Страницы: 14

Бренд: Tavish Design Страницы: 34

QM-AMP3x80 Series

Бренд: Crestron Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды