Matthews VIAcode T100 Скачать руководство пользователя страница 36

Страница: 36 / 47

Maintenance – Ink-Filter Replacement

T50/T100 PTM – User Guide – Version 2 Issue 1

7. Remove the filter from its retaining bracket, then unscrew the

Iink Filter

’

two tube

retaining nuts. Some ink spillage will occur. Make sure that there are paper towels at
hand to absorb any spillage.

Figure 27 - Ink filter

8. Screw the new filter on to the existing

Tube-Retaining-Nuts,

tighten the nuts with finger

pressure only

Make sure that the

Compression-Rings

and

Spacers

inside the

Tube-

Retaining-Nut

s are correctly positioned as shown.

Figure 28 -

Iink Filter

compression ring

9. Inspect the filter to ensure that it is connected correctly and then mount it back in to the

Filter-Retaining-Bracket.

10. Secure the

Reservoir-Cover

back on to the

Ink-Reservoir

11. Make sure that the PTM is correctly mounted as described under

“Mounting the Print

Head”

on page 16.

12. Turn the

Ink-Vent-Screw

, located on top of the

Ink-Reservoir

, fully anti-clock wise.

13. Unscrew and remove the

Nozzle-Protector-Plate

from the front of the PTM.

14. Unscrew and remove the

Ink-Reservoir-Cap

from the

Ink-Inlet

. Store it in a clean place

for future use.

Iink Filter

Tube-Retaining-Nut

Filter-Retaining-Bracket

Compression Ring

Spacer

Содержание VIAcode T100
















































Результаты поиска

Содержание VIAcode T100

Отзывы:

Похожие инструкции для VIAcode T100

Бренды по названию

Популярные бренды

Matthews VIAcode T100, Руководство пользователя

Результаты поиска

Содержание VIAcode T100

Отзывы:

Похожие инструкции для VIAcode T100

Бренды по названию

Популярные бренды