Matrox Solios eA Скачать руководство пользователя страница 72

Страница: 72 / 196

72 Chapter 4: Matrox Solios hardware reference

The following image is the acquisition section of Matrox Solios eA/XA.

On a separate bracket.

Acquisition section of Matrox Solios eA/XA

Video

PCI-X

Bridge

Input

Selector

low

pass

filter

restoration

10-bit

A/D

LUTs

PSG

UART

RS-232

transceivers

Independent

acquisition path

Attenuator,

offset,

and

gain

Clock (LVDS/TTL)

Hsync/Csync
(LVDS/TTL)

✕✕

Vsync (LVDS/TTL)

Trigger (TTL)

Exposure (TTL)

VID_IN

Independent

acquisition

path 3

Independent

acquisition

path 2

Independent

acquisition

path 1

DVI

connectors

(0 and 1)

LVDS/TTL

drivers and

receivers

Opto-

couplers

Aux In

Aux Out

DB-44

and

DB-9

connectors

✝✝

✝✝✝

Only acquisition path 0 is available on Matrox Solios eA/XA Single.

Only two auxiliary outputs are used on Matrox Solios eA/XA Single.
Four auxiliary outputs are used on Matrox Solios eA/XA Dual.

Only one opto-coupled auxiliary input is available on Matrox Solios eA/XA Single.
Two opto-coupled auxiliary inputs are available on Matrox Solios eA/XA Dual.

Independent

acquisition

path 0

✝

✕✕

✝✝

✝✝✝

Only acquistion paths 0 and 1 are available on Matrox Solios eA/XA Dual.

The board can accept an HSYNC or CSYNC input signal, but it can only output an HSYNC signal.

Содержание Solios eA





































































































































































































Результаты поиска

Содержание Solios eA

Отзывы:

Matrox Solios eA, Установка и справочник по оборудованию, Страница: 72 / 196

Результаты поиска

Содержание Solios eA

Отзывы: