Matrox Solios eA Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 196

Matrox Solios eA Скачать руководство пользователя страница 26

26 Chapter 1: Introduction

Handling components

The electronic circuits in your computer and the circuits on Matrox Solios are
sensitive to static electricity and surges. Improper handling can seriously damage
the circuits. Be sure to drain static electricity from your body by touching a metal
fixture (or ground) before you touch any electronic component. In addition, do
not let your clothing come in contact with the circuit boards or components.

Warning

Before you add or remove devices from your computer, always

turn off

the power

to your computer and all peripherals.

Installation

The installation procedure consists of the following steps:

1. Complete the hardware installation as described in

Chapter 2: Hardware

2. Complete the software installation procedure described in the documentation

accompanying your software package.

More information

For information on using multiple Matrox Solios boards, refer to

Chapter 3: Using

multiple Matrox Solios boards

For in-depth hardware information, refer to

Chapter 4: Matrox Solios hardware

; whereas for a summary of this information, as well as environmental and

electrical specifications, and connector pinout descriptions, see

Technical information

This manual occasionally makes reference to a MIL-Lite function. However,
anything that can be accomplished with MIL-Lite can also be accomplished with

MIL, ActiveMIL, ActiveMIL-Lite, or Matrox Inspector.

1

1. Most operations can be accomplished with Matrox Inspector.

«
...
24
25
26
27
28
...
»

Содержание Solios eA





































































































































































































Отзывы:

Нет отзывов