manualshive.com logo in svg

Matrox Solios eA, Установка и справочник по оборудованию, Страница: 151 / 196

Поделиться
Скачать
Matrox Solios eA Скачать руководство пользователя страница 151

 Connectors on Matrox Solios eA/XA      151

To build your own cable, you can purchase the following parts: 

These parts can be purchased from third parties such as Digi-Key Corporation 
(www.digikey.com).

Internal auxiliary I/O connector

The internal auxiliary I/O connector is a 50-pin low-profile IDC connector. It is 
used to transmit control signals and supply power to the adapter board, and to 
transmit/receive the timing and auxiliary signals. The auxiliary signals can be used 
to route synchronization, trigger, exposure, or user-defined signals. 

The connector is located on the edge of the board, making the signals accessible 
from inside the computer enclosure. You can use the connectors on the adapter 
board to access most of these signals from outside the computer enclosure; only 
the most commonly used signals are accessible so that an easily sourced connector 
of a reasonable size can be used. Note that the clock signals are not accessible from 
the adapter board.

The pins for auxiliary signals carry unidirectional signals, unlike those for 
synchronization signals on the DVI connector. This means that using this 
connector, the board can both transmit and receive synchronization signals at the 
same time.

7

P0_OPTO_AUX(TRIG)_IN+

Opto-isolated auxiliary input for acq. path 0 (positive).
Supported signals: trigger input 1 or user-defined input 1.

8

P3_OPTO_AUX(TRIG)_IN+

Opto-isolated auxiliary input for acq. path 3 (positive).
Supported signals: trigger input 1 or user-defined input 1.

9

NC

Not connected.

1. Note that only signals defined for acquisition path 0 (those that begin with P0) apply to the Matrox Solios eA/XA Single board. Only signals defined for acquisition 

paths 0 and 1 (P0 or P1) apply to the Matrox Solios eA/XA Dual board.

Pin

Signal

1

Description

Manufacturer:

NorComp, Inc.

Connector:

172-E09-102-031

Backshell:

970-009-010-011

Содержание Solios eA





































































































































































































Отзывы:

Нет отзывов