Matrix SIMADO GFXD1111S Скачать руководство пользователя страница 13

Страница: 13 / 194

Matrix SIMADO GFXD1111S V3 System Manual

Programming SIMADO GFXD1111S

SIMADO GFXD1111S can be configured either in Mobile-FXS Mode or Mobile-FXO Mode.

Mobile-FXS Mode

, all three ports viz. Mobile, FXO and FXS are functional. By default, system is configured in

this mode of operation.

SE should configure GFXD1111S in one of the following three modes of operation as per the requirement of the
user:

SMS (Default Configuration)

SMS + In Fax + Data

Report Generation

(Refer

“Mode of Operation”

for more details)

Mobile-FXO Mode

, only two ports viz. FXO and Mobile are functional. In this type of configuration, FXS port is

used only for programming the system. This type of configuration is useful when a mobile user wants to access the
station/trunk line of the PBX via GSM/CDMA network. (Refer

“Mobile-FXO Mode”

for more details)

Programming of SIMADO GFXD1111S can be done using following four methods:

Programming through COM Port (Refer

“Programming the System through COM Port”

)

Programming through FXS Port (Refer

“Programming the System through FXS Port”

)

Programming through Mobile Port (Refer

“Programming the System through Mobile Port”

)

Programming using SMS (Refer

“Programming the System using SMS”

)

Содержание SIMADO GFXD1111S



































































































































































































Результаты поиска

Содержание SIMADO GFXD1111S

Отзывы:

Бренды по названию

Популярные бренды

Matrix SIMADO GFXD1111S, Системное руководство

Результаты поиска

Содержание SIMADO GFXD1111S

Отзывы:

Бренды по названию

Популярные бренды