manualshive.com logo in svg

Matrix SIMADO GFXD1111S, Системное руководство

Поделиться
Скачать
Matrix SIMADO GFXD1111S Скачать руководство пользователя страница 105

Matrix SIMADO GFXD1111S V3 System Manual

99

PCO Application

One of the most common applications of SIMADO GFXD1111S is to connect it with the PCO machine for routing 
the call through the cheapest route and provide the correct bill for the same to the caller. SIMADO GFXD1111S is 
connected to the PCO machine as shown in the figure given below:

For PCO application, SIMADO GFXD1111S is to be programmed in Mobile-FXS mode. Also program appropriate 
metering pulse for FXS port, to generate correct billing information on the PCO machine. 

In order that the PCO machine generates the bills properly, the answer signaling information or metering 
pulse should be given either in the form of 12/16 KHz pulses or polarity reversal.

How to program?

Enable/Disable PCO Application

Use following command to enable/disable PCO Application:

500-Flag-#*

Where,

By default, it is disabled.

Answer Signaling on FXS Port

Use following command to program the answer signal to be generated on FXS Port:

221-Answer Signal-#*

Where,

By default, Polarity Reversal is selected.

(Refer 

“Port Parameters-FXS”

 for more details)

Answer Supervision on FXO Port: 

Use following command to program the Answer Supervision Signal on FXO Port:

Flag Meaning

0

Disable

1

Enable

Answer Signal Meaning

0

None

1

Polarity Reversal

 

 

PSTN

 

GSM/

CDMA

Network

FXO

Port

GSM/

CDMA

FXS

Port

PCO Machine

RJ-11

GFXD1111S

COM

Содержание SIMADO GFXD1111S



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды