MasterCraft 2007 MariStar Скачать руководство пользователя страница 79

Страница: 79 / 81

Genuine MasterCraft Parts

2007 MasterCraft Owners Manual - Page 23-1

Genuine MasterCraft Parts

Recognizing the pride that MasterCraft owners take in their boats, MasterCraft has been diligently working to

develop our own line of products designed speciﬁ cally to ensure a better-looking, longer-lasting product.

Your 2007 model ProStar, MariStar or X-Series boat is just the fourth full model year to be able to utilize these

products. As you maintain your boat over the coming years, use Genuine MasterCraft parts (GMP) to keep the pride!

MasterCraft Marine Motor Oil

The life of your marine engine is dependent upon proper lubrication. That is why we’ve developed MasterCraft

Marine Motor Oil. This premium marine motor oil was formulated speciﬁ cally for MasterCraft Boat Company for use in

high-performance marine engines. The oil provides high viscosity and ﬁ lm strength for engine protection in high-load

applications. You cannot get the same formula in any other engine oil!

MasterCraft is designed to protect against corrosion, wear, oxidation, varnish and sludge deposits. When

used as directed in the Owners Manual, this oil assures compliance with MasterCraft warranty requirements. Master-

Craft Marine Motor Oil is an exclusive product available only through genuine MasterCraft dealerships!

MasterCraft Premium All-Purpose Cleaner

Most MasterCraft boat owners pay attention to the details, especially when it comes to the maintenance and

life of the boat interior. We give you information in the Owners Manual on how to extend the life of the boat interiors.

We especially caution to avoid certain household cleaners, powdered abrasives, steel wool and industrial cleaners that

can cause damage and discoloration. Dry cleaning ﬂ uids and lacquer solvents should not be used because they will

remove the printed pattern and gloss.

No cleaner can remove every mark or stain, but we provide a table in the manual that tells the owner what to

use and how to treat many stains. For regular maintenance, however, we’ve never told you what to use—only what not

to use. Now, with this new product, MasterCraft Premium All-Purpose Clear, you can do it right!

A powerful foam cleaner that cuts through grease, dirt and grime, the foam clings to vertical surfaces and

penetrates through dirt that accumulates. MasterCraft Premium All-Purposes Cleaner is an exclusive product available

only through genuine MasterCraft dealerships!

MasterCraft Premium Shine & Protectant

After boat owners get the interior surfaces clean, they like to have a product that will help keep everything

looking ship-shape. Waxes are not recommended for interior surfaces because many contain dyes or solvents that can

permanently damage the protective coating. That’s why MasterCraft developed our own Premium Shine & Protectant

to guard against ultraviolet rays, environmental conditions and everyday use, while adding years of life and beauty.

This product penetrates, protects and beautiﬁ es. It contains no ﬂ uorocarbons either. MasterCraft Premium

Shine & Protectant provides a protective shield that gives a long-last appeal for plastic, plexiglass, vinyl, rubber, acryl-

ics, Formica, wood and leather—so it can be used on more than just the boat!

For best results, consumers should leave the Shine & Protectant on surfaces for several hours or overnight before

removing any excess. This product is available only through genuine MasterCraft dealerships.

MasterCraft Premium Marine Wax

If you take great pride in the appearance of your boat, by using MasterCraft Premium Marine Wax you help

ensure a long-lasting and attractive shine for the deck and hull. This pre-softened formula combines carnauba wax with

efﬁ cient cleaning agents that remove oxidation, engine exhaust spill-off and other contaminants. MasterCraft Premium

Marine Wax provides a deep gloss with long-lasting protection from UV rays, salt air and harsh weather conditions.

It’s great for ﬁ berglass, gel coat, aluminum, chrome and painted surfaces.

This product protects and inhibits color fading and cleans effectively without harmful abrasives, leaving a

beautiful glossy shine. It protects against harsh weather conditions, too. Using this GMP product will assist boat owners

in following the requirements outlined in the Owners Manual for providing protection over the life of the boat.

MasterCraft Premium Marine Wax is an exclusive product available only through genuine MasterCraft dealerships!

Содержание 2007 MariStar


















































































Результаты поиска

Содержание 2007 MariStar

Отзывы:

MasterCraft 2007 MariStar, Руководство пользователя, Страница: 79 / 81

Результаты поиска

Содержание 2007 MariStar

Отзывы: