MasterCraft 2007 MariStar Скачать руководство пользователя страница 6

Страница: 6 / 81

2007 MasterCraft Owners Manual - Page iv

before operating again or have your boat serviced by your local MasterCraft dealer. Note that damage to your engine

from neglected oil problems can be costly to repair. Such damage is not covered by your warranty. (Page 5-3)

CAUTION used without the safety alert symbol indicates a

potentially hazardous situation which, if not avoided, may

result in property damage.

1: To ensure proper break-in and lubrication, boat owners should not remove the factory break-in oil until after the

initial ten (10) hours of operation. At that time, an oil change should be performed by an authorized MasterCraft

service technician/your local MasterCraft dealer. (Page 8-1)

2: DO NOT use the ski pylon for lifting. It is NOT designed as a central lifting point. Also, DO NOT use the stern ski

tow as a lifting ring. The deck will be damaged. See the Storage Cradle sub-section of the Lifting the Boat section

of this Manual. Also never lift a boat with a large amount of water in the bilge or containing a water-ﬁ lled device

such as a Fat Sac or ballast system. The extra stress will put an excessive load on the hull and lifting equipment that

may seriously damage the boat and void your warranty. (Page 11-1)

3: Continued operation after the warning light has illuminated may

cause severe damage. This will void your warranty. (Page 9-3)

4: Because of the complexity of preparing your boat for proper

winter storage, as well as the possibility of extreme damage to

the engine if a preparation error was made during winterization,

MasterCraft recommends that you schedule an appointment with

your local MasterCraft dealer and permit the dealer to perform

the winterization procedures. (Page 17-1)

5: Add-on equipment may adversely affect the alternator output or

overload the electrical system. Any damage caused as a result will

not be covered by, and may void, your warranty. (Page 15-3)

6: Ignoring elevated temperatures on a temperature gauge or any

other evidence of the engine operating at temperatures above

recommended levels can result in serious damage to the engine.

Any resulting damage will not be covered by, and may void, your

warranty! (Page 15-4)

7: Failure to follow the engine oil recommendation listed in the man-

ual can cause additional engine wear and increase the possibil-

ity of engine component failure. Damage to your engine due to

incorrect oil usage can be costly to repair, and is not covered by

your warranty! (Page 8-2 and 15-10)

8: Failure to maintain your coolant at the proper level can cause engine damage. Your warranty will not cover engine

damage due to overheating or any other cause associated with improper coolant levels. (Page 15-2)

9: Do not operate the starter motor continuously for more than ﬁ fteen (15) seconds without at least a two (2) minute

“cool-down” period. Failure to do so may cause the starter to overheat, resulting in damage. Failure to release the

ignition key after the engine has started may cause damage to the starter motor and drive. (Page 9-2)

10: Damage to the engine by use of low-quality gasoline or gasoline with an octane rating below the minimum level

listed will void the warranty on your boat. (Page 6-2)

Содержание 2007 MariStar


















































































Результаты поиска

Содержание 2007 MariStar

Отзывы:

MasterCraft 2007 MariStar, Руководство пользователя, Страница: 6 / 81

Результаты поиска

Содержание 2007 MariStar

Отзывы: