Dear customer, thank you for purchasing a MASTER product. This manual describe the operations for a correct installation of the product. This device is not design for a continuative
use. Use of the product other than that provided for in this manual is improper and prohibited and will void the warranty and any manufacturer's liability. The installation of the product
must be done by a qualified technician. At the end of the installation, all manuals must be given to the end user. Keep this manual for future reference!
The technical characteristics of the motor are shown in the label applied to the motor tube. The common characteristics of the motor family are:
Power supply
: 230 Vac 50 Hz
Stand-by comsuption
: < 1W
Minimum roller diameter
: 50 x 1.5 mm
IP insulation
: Ip44
Insulation class
: H
Continuos operating time
: 4 minutes
Operating radio frequency
: 433.42 MHz
N° of memorizable transmitter
: 40
01. TECHNICAL SPECIFICATIONS
02. WARNINGS
PRODUCT INFORMATION
Incorrect installation can cause serious injuries
Keep these instructions for future maintenance work and disposal of the product
All the product installation, connection,
programming and maintenance operations must be carried out only by a qualified and skilled technician, who must comply with laws, provisions, local regulations and the instructions
given in this manual
The wiring must comply with current IEC standards. The final electrical system must be created only by the electrician
Some applications require hold-to-run
operation and can exclude the use of radio controls or require particular safety devices
To prevent potentially dangerous situations, check the operating condition of the roller
shutter/awning regularly
●
●
●
●
●
02.1 Warnings for safety
Before installing the product, check the compatibility with the associated devices and accessories
Check that the package is intact and has not been damaged in transit
A heavy
knock and the use of unsuitable tools can cause the damage of the external or internal parts of the motor
Do not pierce or tamper with the motor in any way. Do not modify or replace
parts without the manufacturer's permission
Do not carry the motor by the power cable. The product may not be used if the power cable is damaged. Do not try to replace the power
cable
Any screws needed to complete the installation must not come into contact with the motor
The power of the motor must be sufficient for the applied load (check the rated data
shown on the motor)
Some stages of programming and/or normal operation make use of the mechanical stops of the roller shutter/awning. It is essential to choose a motor with the
most suitable torque for the application, considering the actual traction of the roller shutter/awning, and to avoid motors that are too powerful
Use winding rollers that are at least
1mm thick
Leave 1-2 mm of right/left play on the winding roller
Check that the shape and size of the drive pulley and adapter crown correspond to the winding roller used. Adapters,
supports and sundry accessories related to the motor must be chosen exclusively from the MASTER catalogue
If the product is installed at a height of less than 2.5 m from the floor
or from another support surface, the moving parts must be protected with a cover to prevent accidental access. In any case, ensure access for maintenance work
The power cable
must be positioned in such a way that it does not come into contact with moving parts
The power cable of the product is suitable for indoor installation only. If installed outside, place
the cable in a protective tube
Position the buttons within sight of the roller shutter/awning but a long way from its moving parts. Position the buttons more than 1.5 m from the floor
The motors are designed for residential use; the maximum continuous operating time is 4 minutes
During operation, the motor body becomes very hot, so be careful
The motor
contains a self-resetting thermal cut-out, which stops the motor if it overheats. The motor returns to normal operation when its temperature drops below the safety limit (normally after 5
to 10 minutes)
The motor must be installed so that it cannot come into contact with liquids and in any case in a position protected from atmospheric agents
For your safety, do not
work near the winding roller while the motor is powered
Where possible program the upper limit of the motor by contact with an obstacle. This solution will allow the motor to
automatically recalibrate the limit switches recovering slight deviations due to adjustment of the roller or a continuous and sudden power loss
If there are several radio appliances in
the same system, they must not be less than 1,5m apart
Do not install the product near metal surfaces
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
The product is not intended to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are
supervised or given instructions about the product way of use by a person responsible for their safety
Check the automation during the movement and keep people at a safe
distance, until the movement ends
Do not allow children to play with the appliance or with the fixed control devices
Do not operate the blind when maintanance operations are
being carried out (e.g. window cleaning, etc.). If the control device is automatic, disconnect the motor from the power line
●
●
●
02.2 Warnings for installation
02.3 Warnings for use
01
USER MANUAL
tubular motor Ø45 mm with electronic limit switch
R
rev01_1 20.05.2019
MODO
MODO has been designed to drive drop awning, specially for structures where there are manual or automatic hooks placed near the lower
limit switch.
The motor is equipped with systems for recognizing any obstacles during the down phases (only if a offset adapter has been correctly
installed, see section "03 INSTALLING THE OFFSET ADAPTERS"). If the drop awning is equipped with cassette and the motor is equipped
with a offset adapter, during the installation the product is able to automatically detect and memorize the limit switches. Moreover, the
presence of the cassette will allow the motor to independently recover any deviations from the limit switches due to adjustment of the drop
awning or other possible error factors; it is therefore recommended to always install the drop awning with cassette.
If you proceed with the installation in the absence of the cassette, it may occasionally be necessary to adjust the limit switches.
If the drop awning is not installed properly, the motor may detect non-existent obstacles during the up or down movements. In this case it is
necessary to verify the installation.
Information for any assistance requests
To facilitate, improve and speed up any request to the assistance service it is necessary to provide the product name to the operator.
Before installing the motor, it is recommended to copy the technical data (including the extended product name) and store them in a safe place
It is advisable
(for example, near police stations, airports, ports, hospital, etc). A technical inspection is in any case advisable before installing
any radio system in order to identify sources of interference. Radio systems can be used where possible disturbances or malfunctioning of the transmitter or the receiver do not cause a risk factor, or if the risk factor
is cancelled by suitable safety systems. The presence of radio device operating on the same transmission frequency (
) can interfere with the radio receiver of the motor and so reduce the range of the
system and limit the functionality of the installation.
to avoid using radio systems in areas with strong interference
433,42 MHz
Notes on radio systems
MASTER uses packaging recyclable materials. Dispose materials on the proper containers, complying with the law in force in your locality.
This product may have substances that are polluting for the environment and dangerous for the health.
At the end of the product life cycle, carefully comply with the waste disposal rules. It is strictly forbidden to dispose the product on the domestic waste.
Disposal