manualshive.com logo in svg

masosine SPS 100, Руководство пользователя

Поделиться
Скачать
masosine SPS 100 Скачать руководство пользователя страница 3

1

Declaration of conformity

 

Rev. 02 / 04.01.2021 

 

 

EC/EU Declaration of Conformity (English translation)  

for the purposes of Directive 2006/42/EC Annex II 1.A 

 

1.  Manufacturer: 

Watson Marlow GmbH, Steinbeisstr. 3, 74360 Ilsfeld (Germany),  
Phone: +49(0)70629560-0 

 

2.  Name and address of the authorised documentation officer: 

Watson Marlow GmbH, Steinbeisstr. 3, 74360 Ilsfeld (Germany) 
 

3.  Product 

: 

MasoSine Pump

 

 

Type deignation 

: 

Certa, Certa Plus, SPS, MR, EcoSine

 

 

 

 

 

4.  The above-mentioned manufacturer declares on his own responsibility that the product / 

machine conforms to all regulations of this EC directive: 

2006/42/EG  

Directive 2006/42/EC of the European Parliament and of the 
Council of 17 May 2006 on machinery and amending Directive 
95/16/EC (recast) (1 ) Official Journal of the EU: L 157/24 of 
09.06.2006 

The above-mentioned manufacturer further declares that the product / machine is in conformity 
with the following additional EC/EU directives or relevant regulations: 

2014/30/EU 

Directive 2014/30/EU of the European Parliament and of the 
Council of 26 February 2014 on the harmonisation of the laws of 
the Member States relating to electromagnetic compatibility 
(recast), Official Journal of the EU: L 96/79 of 29.03.2014 

 

 

 

Directive 

2014/35/EU

 was complied with in accordance with Annex I No. 1.5.1 MRL 

2006/42/EC with regard to its protection objectives. 
 
According to Directive 

2014/68/EU, Artikel 4.3

 the above mentioned manufacturer certifies in 

"accordance with the applicable good engineering practice" that the design and manufacture 
ensures that the pump can be used safely according to the operating data on the nameplate 
and in the instruction manual. 

 

 

5.  The following harmonised standards - or parts thereof - have been applied: 
 

EN ISO 12100: 2011-03 

Safety of machinery - General principles for design - Risk 
assessment and risk reduction 
 

 

EN ISO 13857: 2008 

Safety distances against reaching of hazardous areas 
 

 

EN 809: 1998+A1:2009 + 
AC:2010 

Pumps and pump units for liquids - General safety requirements 

 

 

The following other technical standards/specifications - or parts thereof - were applied:  
 

DIN EN 10357:2014-03

  Longitudinally welded stainless steel tubes for the food and chemical     

                                        industry 

DIN 11851

  Dairy pipe fittings 

DIN 11864

  Aseptic tube shipments 

 

 

 

 

 

Ilsfeld, 04.01.2021 

   

 

Ort, Datum 

 

Ewald Warmuth (Managing Director) 

 
 

m-SPS-en-08

3

Содержание SPS 100












































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды