manualshive.com logo in svg

Masoneilan SVI II ESD, Руководство по установке и обслуживанию

Поделиться
Скачать
Masoneilan SVI II ESD Скачать руководство пользователя страница 165

Masoneilan SVI II ESD Installation and Maintenance Manual 

=

|

 

165

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

Air Consumption

0.212 scf/min. (6 sL/min.) at 30 psi (2.1 bar, 207 kPa) supply 
0.282 scf/min. (8 sL/min.) at 60 psi (4.14 bar, 414 kPa) supply 
0.424 scf/min. (12 sL/min.) at 90 psi (6.21 bar, 621 kPa) supply
0.529 scf/min. (15 sL/min.) at 120 psi (8.28 bar, 828 kPa) supply

Air Supply Failure 

Single Acting Relay
On supply failure the actuator output drops. Some overshoot can occur when air 
pressure returns after a period without air supply pressure. Always set control set 
point to 0%, and put process control system in manual, for smooth recovery from 
air supply failure.

Loss of Input Signal

Output drops to low pressure.

Output Pressure

120 psi (8.28 bar, 828 kPa) max

CV

0.59 filling, 0.72 venting

Sweet Natural Gas

H

2

S content not more than 20 ppm

Table 21 Control Valve Mounting System

Non-contact Hall Effect Position Sensor (18º to 140º rotation)

Rotary NAMUR Mounting Kit per VDI/VDE 3845

Reciprocating Kits Available

Table 22 ESD and Diagnostic Capabilities

Diagnostics

EC61508 compliant up to SIL3 certified by TUV and EXIDA
Partial Stroke Testing Initiation (HART

®

, Analog, Local Pushbutton, Built-In Scheduler)

Digital Output for PST results and SVI II ESD Health 
Non-volatile memory for two (2) PST signature 
Non-volatile memory for ESD Shutdown Event Signature
Safety Trip Trigger: 4/20 mA or 24 VDC input
Local PST scheduler with built-in calendar
Full Stroke Valve Signature & Positioner Diagnostics
Built-In Explosion Proof External LCD with Pushbuttons

Language Support

English, Japanese, French, Portuguese, German, Spanish, Italian

Table 20 Pneumatics Single Acting Standard Flow (Continued)

Air Supply 

Dry, oil-free, 5 micron filtered air (See ISA S7.3)

Содержание SVI II ESD





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды