Masoneilan SVI II ESD Скачать руководство пользователя страница 161

Страница: 161 / 220

Masoneilan SVI II ESD Installation and Maintenance Manual

161

Appendix A. Specifications and References

Physical and Operational Specifications

This section provides physical and operational specifications for the SVI II ESD. Specifications are
subject to change without notice.

Table 14 Environmental Specifications

Operating Temperature Range

-40 °F to 185 ° F (-40 °C to 85 °C)

Storage Temperature Limits

-58 °F to 200 °F (-50 °C to 93 °C)

Temperature Effect

< 0.005% / °F typical; -40 °F to 180 °F (< 0.01% / ° C typical; -40 ° C to 82 °C)

Supply Pressure Effect

0.05% per psi (.73% per bar)

Relative Humidity

10 to 90% non-condensing

Humidity Effect

Less than 0.2% after two days at 104 °F (40 °C), 95% Relative Humidity.

Insulation Resistance

Greater than 10 G Ohms at 50% RH.

MTBF

49 years based on MIL handbook calculation for electronic parts and field
data on mechanical parts

Electromagnetic Compatibility
Electrostatic

Electrostatic discharge — No effect with contact discharge level of 4KV
and air discharge level of 8 KV
(IEC 1000-4-2)
Radio frequency interference — Less than 0.2% at 10 V per meter (EN
50140)

Fast Transient Burst

No effect at 2 KV (Coupling clamp IEC 1000-4-4).

Vibration Influence
Measured at SVI II ESD Housing

4 mm at 5 - 15 Hz - Negligible
2 G at 15 - 150 Hz Less than 2% of span
1 G at 150 - 2000 Hz - Less than 2% of span

Содержание SVI II ESD




























































































































































































































Результаты поиска

Содержание SVI II ESD

Отзывы:

Бренды по названию

Популярные бренды

Masoneilan SVI II ESD, Руководство по установке и обслуживанию

Результаты поиска

Содержание SVI II ESD

Отзывы:

Бренды по названию

Популярные бренды