Masoneilan SVI II ESD Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 220

Masoneilan SVI II ESD Скачать руководство пользователя страница 140

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

140

|

BHGE

Upgrading Firmware

SVI II ESD is equipped with a nonvolatile re-writable Flash Memory for program storage. The
firmware can be updated as improvements and advances are made in the embedded
programs that operate the SVI II ESD. Firmware improvements for SVI II ESD can be obtained
by contacting the factory.

Tools Required

HART

®

modem

PC with Windows 2000, XP or later, 16 MB RAM

ValVue ESD software or later (provided with software upgrade on CD-ROM)

Installing Firmware Upgrade

It is recommended that configuration is uploaded and saved prior to installation procedure.
Follow ValVue ESD instructions to save the old configuration. Follow the detailed instructions
included with the software update.

To check firmware version cycle the power off, then on, to perform a cold start. The display
shows software version in upper right corner. When maintenance is complete reinstall the
positioner and perform checkout procedure detailed in “Installation and Setup” on page 57.
Consult factory for firmware upgrade services. ValVue ESD is the recommended tool for
complete re-configuration. See “Configuration and Calibration” on page 89.

«
...
138
139
140
141
142
...
»

Содержание SVI II ESD





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды