Installing the Gas Fireplace
hearth extension of about 20
” (twenty inches) at the fireplace’s
opening and about 12
” (twelve inches) extension at each side.
These relative dimensions are also covered by code. Note
that it is required that metal safety strips must be laid on the
floor of the non-combustible raised platform. These should be
26 gauge and measure 4
” (four inches) wide. They need to
extend half way under the platform and half way under the
hearth extension material (see Fig. 14-1).
Attention:
You will note that there will be a gap between
the fireplace front and the extension of the non-combustible
hearth material. Be certain that you seal this with non-
combustible material.
Mantle and Mantle Shelf Clearances
As with any radiant heat fireplace, all MASON-LITE Fireplaces
must comply with building code safety clearances, for units
that have openings of 6 sq. ft. (six square feet) or greater.
For Mantel clearances see Fig. 10-2.
Walls that Adjoin - your fireplace cannot be installed closer
than 2 ft. (two feet) to any adjoining walls in the room where
the fireplace is.
Caution in Regards to Combustibles - If any part of the
fireplace or objects in the room (curtains, rugs, paint, cushions,
etc.) start to show warping or discoloration due to heat from
the fireplace, it is time to take immediate action. Do not use
the fireplace until you have figured out how to address the
problem. You are facing a potential fire hazard. MFI cannot be
responsible for the make-up of material on the exterior of the
fireplace you have chosen, nor can MFI be held responsible
for the materials in a room that may be responding negatively
to heat. However, in almost all cases, there is a solution to
the problem, either by making adjustments to airflow or the
modifications to the room itself.
Installing Outside Combustion (make-up) Air
1) The Mason-Lite Fireplace needs enough make-up air to
function properly and some local building codes may require
outside combustion air to be provided. If no make-up air is
provided, improper flue drafting may occur, creating negative
pressure whereby smoke may enter the home, especially in
homes that are very well insulated and tightly sealed. Check
local building codes for specific requirements.
2) Install Combustion Air Kit MFP4-AK into the MASON LITE
Firebox through the side wall opening provided. The tubing
that goes out of the firebox wall must feed into a flexible
metal conduit as the source for outside combustible air. It can
go straight out through an outside wall or into a ventilated
crawl space. If crawl space is used, check codes for proper
termination.
3) Be sure that you carefully check the source of the outside
air before you choose the site for your air intake. You don
’t
want a place where snow will collect, where bushes or trees
will be growing or a location that is too close to any other
structure.
4) Install a screened termination cap to keep out animals.
Adding a Gas Pipe
You may elect to add a vented decorative gas appliance (gas
log) to your Mason-Lite Fireplace. If so, follow the installation
instructions from the Decorative Gas Appliance manufacturer.
Familiarize yourself with requirements for installation as
outlined by the National Fuel Gas Code, ANSI Z223.1. This
gas pipe provision should only be used on a decorative gas
appliance.
1) You can route the gas piping practically anywhere in the
firebox - the floor, back wall or side walls. You will just need a
masonry drill; the instructions from the gas appliance
manufacturer will be very straightforward.
2) Fill in the holes you have drilled around the gas piping with
the regular MASON-LITE mortar.
3) Follow the Gas Log manufacturer
’s instructions.
Adding Electrical Connection
Like the gas line, electrical feed lines can be run through the
floor, back wall, or side walls. Follow local building and
electrical code requirements.
MASON-LITE Chimney Systems:
The Mason-Lite Fireplace requires the following chimney
system(s):
All chimney systems must be installed with an anchor plate
installed on top of unit. Installers are cautioned to put the
chimney system together exactly as instructed and shown in
chimney manufacturer
’s guide. Any variations may have
serious consequences resulting in an accident or malfunction. If
instructions are not followed, the warranty on the product will
become null and void.
Note that the most important aspect of the installation is
maintaining the minimum required clearances to combustible
materials according to the chimney pipe manufacturer
’s
recommendations, otherwise a potential fire hazard may
occur.
Warning: do not interchange chimney manufacturer
’s parts
with any other parts except those specifically required by
the chimney manufacturer
’s recommendations otherwise a
potential hazardous condition may be created.
Attention: When choosing a Chimney System it must meet
the following requirements:
•
Designed for installation in accordance with the National
Fire Protection Standard and UL 103.
•
Meets the requirements of NFPA 211.
•
Designed in accordance with ICC Codes.
REV 1 - 0907231405
16
L-A2-27509
