Marvell GT-64260A Скачать руководство пользователя | Manualshive

Страница: 91 / 163

background image

CPU Interface Design Considerations

CPU Interface Connectivity

Copyright © 2002 Marvell

CONFIDENTIAL

Doc. No. MV-S300165-00, Rev. A

May 21, 2002, Preliminary

Document Classification: Proprietary Information

Page 91

Section 14. CPU Interface Design Considerations

The CPU interface is used to connect the GT-64260A and the CPU.

The GT-64260A CPU interface is a 60x bus compatible master and slave. In addition, it is a MPX bus compatible
slave.

Note

As an MPX bus compatible slave, this interface only supports "address only bus mastering" for snooping

capability.

The GT-64260A CPU interface internal 60x arbiter supports up to two external 60x masters and the GT-64260A
60x master. The MPX internal arbiter supports one external MPX master and the GT-64260A MPX master, for
address only transactions. In Multi-GT mode, the GT-64260A supports up to four slaves connected on the same
60x bus.

The GT-64260A CPU bus configuration and internal bus arbiter and multi-GT support is sampled at reset accord-
ing to the following configuration.

14.1 CPU Interface Connectivity

The CPU bus connectivity is according to the 60x/MPX specification

Table 13:

CPU Interface Configuration at Reset

Pin(s)

Configuration Function

AD[7:6]

CPU Bus Configuration

00-
01-
10-
11-

60x bus
MPX bus
Reserved
Reserved

AD[8]

Internal 60x bus Arbiter

0-
1-

Not supported
Supported
If using the MPX bus mode, AD[8] must be set to 1.

AD[9]

Multiple GT-64260A Support

0-
1-

Not supported
Supported

«
...
89
90
91
92
93
...
»

Содержание GT-64260A




































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GT-64260A

Бренд: UE Страницы: 4

Бренд: XBOX Страницы: 7

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

Бренд: Aalborg Страницы: 15

Бренд: Aalborg Страницы: 48

CITY ELITE SINGLE

Бренд: Baby Jogger Страницы: 3

Бренд: Fantech Страницы: 2

Бренд: Saga Страницы: 9

Бренд: Zaiput Flow Technologies Страницы: 10

Бренд: WAGNER Страницы: 128

Бренд: SMC Networks Страницы: 10

Бренд: Velux Страницы: 11

Бренд: Kantronics Страницы: 201

CITY MICRO DOUBLE

Бренд: Baby Jogger Страницы: 9

Бренд: Kong Страницы: 2

Airedale Sentinel

Бренд: Modine Manufacturing Страницы: 2

Бренд: D+H Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды