9
NOTE
warmer respectively. When you have reached your desired
set-point temperature, press the "On/Off" keypad to accept,
or do nothing and the "Set" mode will time-out in 10-sec
-
onds accepting the displayed temperature as the new
set-point.
The available set-point temperature range for your appli
-
ance is -6°F (-21°C) to 6°F (-14°C) for the freezer compart
-
ment and 34°F (1.2°C) to 42°F (5.7°C) for the refrigerator
compartment. If you attempt to adjust the temperature out
-
side of these ranges you will receive an audible notification.
Freezer
compartment
selected
Refrigerator
compartment
selected
REF
FRZ
REF
FRZ
Temperatures can be set for each individual compartment
(refrigerator or freezer / ice-maker). To do so you must first
select the compartment you want to set the temperature for.
You do so by pressing the refrigerator (REF) or freezer
(FRZ) button on the display. When pressed the LED light
will be illuminated for the respective display.
To change the set temperature for a particular compart
-
ment, with the compartment enabled and out of sleep
mode, press the "-" or "+" keypads. "SET" will be indi
-
cated on the user interface panel and the current set-point
temperature will display and flash. Subsequent presses of
the "-" or "+" keypads will adjust the temperature colder or
Adjusting the temperature:
When initially loading your product with warm contents, it
may take up to 48-hours for the storage compartment tem
-
perature to stabilize.
When making temperature set-point changes, it may take
up to 24-hours for the stored contents to stabilize at your
new set-point temperature.
Factors that affect the storage compartment stabilized
temperature:
• Changes to temperature setting.
• Room temperature changes.
• Temperature of stored contents.
- Loading warm contents.
- Cold content load will delay the change to a warmer
set-point temperature.
- Warm content load will delay the change to a colder
set-point temperature.
• Usage, (number and duration of the door openings).
• Use of the storage compartment display lighting, (glass
door product only).
• Installation of the appliance in direct sunlight or next to
a heat source.
Turning your appliance ON and OFF:
If the appliance is "On", (and out of sleep mode) the tem
-
perature will be shown in the display area of the control.
To turn the appliance "Off", press and hold the "On/Off"
keypad for 4-seconds. "OFF" will now be displayed on the
control.
To turn the appliance "On", press and hold the "On/Off"
keypad for 4-seconds.
USING YOUR ELECTRONIC CONTROL
Temperature mode:
The temperature mode is preset from the factory in Cen
-
tigrade (°C) but you have the option to change it to Fahr
-
enheit (°F). To change the mode, press and hold the "-"
keypad, while pressing the "+" keypad, then release the "-"
keypad. The temperature will now be displayed in Fahren
-
heit (°F). Repeat the procedure to change the temperature
mode back to Centigrade (°C).
Control lock:
The control panel can be locked to avoid unintentional
changes. To lock the control, press and hold the "Lock" key
-
pad until the display reads "Loc" then immediately release
your finger from the keypad. The lock icon will flash 3-times
and then continuously illuminate. When the control panel is
locked, only the Lock keypad, System Status OK indicator
, and the Alarm indicator are active. To un-lock the control
panel, repeat this instruction until the display reads "nLc"
then immediately release your finger from the keypad.
NOTE
If the control lock is active (illuminated lock icon) the
control will have to be unlocked before using the key
-
pad to reset an alarm condition. See page 9 (Control
Lock) for instructions for unlocking the control.
