background image

Martin Audio – MA1400 Amplifier

E

NGLISH

1

CONTENTS (ENGLISH)

Page No

1

CONTENTS      MA1400 USER GUIDE

1

2

APPROVALS

2

3

WARNINGS

2

3.1

EXPLANATION OF GRAPHICAL SYMBOLS

2

3.2

WARNING

2

3.3

CAUTION

2

3.4

IMPORTANT SAFETY INSTRUCTIONS

2

3.5

USER RESPONSIBILITY

3

3.5.1

LOUDSPEAKER DAMAGE

3

3.5.2

SPEAKER OUTPUT HAZARD

3

3.5.3

RADIO INTERFERENCE

3

4

INTRODUCTION

4

4.1

UNPACKING

4

4.2

FRONT PANEL

4

4.3

REAR PANEL

5

5

REAR PANEL FEATURES

5

5.1

GAIN SWITCH

5

5.1.1 THE DIP-SWITCH

6

5.1.2

SENSITIVITY

6

5.1.3

OPTIONS

6

5.2

LINK SWITCH

6

5.3

OPERATING MODES

6

5.3.1

STEREO MODE

6

5.3.2

NOTES FOR AMPLIFIER TESTING

6

5.3.3

TANDEM MODE

7

5.3.4

BRIDGE MONO MODE

7

5.3.5

BRIDGE MONO MODE FEATURES

7

6

INSTALLATION

8

6.1

MOUNTING

8

6.2

COOLING

8

6.3

OPERATING VOLTAGE

8

6.4

GROUNDING

8

6.5

POWER CONSUMPTION

9

6.5.1

CALCULATION

9

7

CONNECTIONS

10

7.1

INPUT CONNECTIONS

10

7.1.1 BALANCED INPUTS

10

7.1.2

UNBALANCED INPUTS

10

7.2

CONNECTING SPEAKERS

11

8

OPERATION

12

8.1

OPERATING PRECAUTIONS

12

8.2

POWERING UP – SOFT START

12

8.3

INPUT ATTENUATORS

12

8.4

INDICATORS

12

9

PROTECTION FEATURES

13

9.1.1

OUTPUT LIMITER

13

9.1.2

THERMAL PROTECTION

13

9.1.3

VHF PROTECTION

13

9.1.4

SHORT CIRCUIT PROTECTION

13

9.1.5

AC MAINS VOLTAGE PROTECTION

13

9.1.6

DC PROTECTION

13

10

MAINTENANCE

14

10.1 TROUBLESHOOTING

14

11

WARRANTY

15

12

SPECIFICATIONS  MA1400

16

All material © 2007. Martin Audio Ltd. Subject to change without notice.

Содержание MA1400




















Отзывы: