background image

13

WARRANTY 

General
The MA1.6 Powered Amplifier is warranted to be free from defects in
components and factory workmanship under normal use and service, for a
period of one year from the date of original purchase.  During the warranty
period, MARTIN AUDIO LTD or its nominated agents, will undertake to
repair, or at its discretion, replace this product at no charge to its owner,
when failing to perform as specified, provided the unit is returned
undamaged, in its original packaging, shipping pre-paid, to the factory,
distributor or authorised service facility.

This warranty shall be null and void, if the product is subjected to:
1) 

Repair work or alteration by person other than those authorised by 
MARTIN AUDIO LTD or its agents.

2) 

Shipping accidents, act of God, war, civil insurrection, misuse, abuse, 
operation with incorrect AC voltage, operation with faulty associated 
equipment, exposure to inclement weather conditions and normal 
wear and tear.  Units, on which the serial number has been removed 
or defaced, will not be eligible for warranty service.

3) 

MARTIN AUDIO LTD shall not be responsible for any incidental or 
consequential damages, with respect to the products warranted.

MARTIN AUDIO LTD reserve the right to make changes or improvements in
design or manufacturing, without assuming any obligation to change or
improve products previously manufactured.

This warranty is exclusive and no other warranty is expressed or implied.
This warranty does not affect your statutory rights.

International
Please contact you supplier for this information, as rights and disclaimers
may vary from county to country.

Martin Audio – MA1.6 Power Amplifier

E

NGLISH

22

>

CONTENTS

<

PRINT

GUIDES

Содержание MA1.6


























Отзывы: