Martin Audio CDD Series Скачать руководство пользователя страница 51

Страница: 51 / 64

CDD

User Guide V1.1

CDD

USER GUIDE

CSX112-F, CSX212-F

Notes

(1)

Measured on-axis in half space at 2 metres, then referred to 1 metre.

(2)

AES Standard ANSI S4.26-1984.

(3)

Measured in half space at 2 metres with 2.83 V input, using band limited pink noise,

then referred to 1 metre.

(4)

Calculated in half space at 1 metre.

CSX112-F

CSX212-F

TYPE

Compact, single driver, direct radiating

subwoofer

Compact, dual-driver, direct radiating

subwoofer

FREQUENCY

RESPONSE

48 Hz-150 Hz ± 3 dB, -10 dB @ 35 Hz

DRIVER

12” (300 mm)/3” (75 mm) voice coil, long

excursion, ferrite magnet, waterproof cone

2 x 12” (300 mm)/3” (75 mm) voice coil,

long excursion, ferrite magnet, waterproof

cone

RATED POWER

400 W AES, 1600 W peak

800 W AES, 3200 W peak

RECOMMENDED
AMPLIFIER

MA3.0

MA5.2K

SENSITIVITY

102 dB

105 dB

MAXIMUM SPL

128 dB continuous, 134 dB peak

134 dB continuous, 140 dB peak

NOMINAL IMPEDANCE

8 ohms

4 ohms

DISPERSION (-6 dB)

Omnidirectional

CROSSOVER

80–120 Hz, via DX0.5 or DX2 controller

ENCLOSURE

52 litre, high-density MDF

100 litre, high-density MDF

FINISH

Black or white textured paint

PROTECTIVE GRILLE

Black or white perforated steel

CONNECTORS

Low-profile 20 A push-lock

WR models only: weatherproof cover with

gasket seal and cable gland

Low-profile 20 A push-lock

WR models only: weatherproof cover with

gasket seal and cable gland

PIN CONNECTIONS

Left to right: Input+, Input -, Link -, Link+

ENVIRONMENTAL

IP24 (Model CSX112-FWR only)

IP24 (Model CSX212-FWR only)

DIMENSIONS

(W) 487 mm x (H) 385 mm x (D) 410 mm

(W) 19.2 in x (H) 15.2 in x (D) 16.1 in

(W) 872 mm x (H) 385 mm x (D) 437 mm

(W) 34.3 in x (H) 15.2 in x (D) 17.2 in

WEIGHT

21.5 kg (47.3 lb)

39 kg (86 lb)

Содержание CDD Series

































































Результаты поиска

Содержание CDD Series

Отзывы:

Похожие инструкции для CDD Series

Бренды по названию

Популярные бренды

Martin Audio CDD Series, Руководство пользователя

Результаты поиска

Содержание CDD Series

Отзывы:

Похожие инструкции для CDD Series

Бренды по названию

Популярные бренды