Marport Trawl Explorer Скачать руководство пользователя страница 44

Страница: 44 / 94

Trawl Explorer | V5 | System Configuration and Display

System Configuration and Display

Learn how to configure the receiver to be able to receive and display Trawl Explorer sensor data.

Note:

This guide refers to the following versions: Scala 01.06.06-01.06.34, Scala2 02.02. If

you use another version, the visual interface and options may vary.

Adding the Sensor to the Receiver

You need to add the Trawl Explorer to the receiver in order to display sensor data on Scala/Scala2.

About this task

The Trawl Explorer is compatible with the following M3/M4/M5/M6 receiver and Scala versions:

Mx version

Scala/Scala2 version

NBTE V1 (FIRM121)

all

NBTE V2 (FIRM126)

03.01.23 or later

all

NBTE V3 (FIRM128)

04.02.28 or later

01.02.05 or later

Adding the Sensor with a Configuration File

You can add the sensor to the receiver with a configuration file that contains the sensor settings
you configured on Mosa2.

Before you begin

• You have exported an XML file containing the sensor settings (See

Exporting Sensor

Configuration Settings for the Receiver

on page 41).

Important:

You need to have

Firefox version 22 to 51

Procedure

Enter your receiver IP address in Firefox web browser to access the system control panel web
page.

Note:

Default IP addresses are: 192.168.10.177 for M3 and M6 receivers, 192.168.1.170 for

M4 receiver. Add the address as a bookmark in Firefox to easily connect to it.

From the left side of the page, click

Sensors

Содержание Trawl Explorer































































































Результаты поиска

Содержание Trawl Explorer

Отзывы:

Похожие инструкции для Trawl Explorer

Бренды по названию

Популярные бренды

Marport Trawl Explorer, Руководство по обслуживанию

Результаты поиска

Содержание Trawl Explorer

Отзывы:

Похожие инструкции для Trawl Explorer

Бренды по названию

Популярные бренды