Marport Trawl Explorer страница 41 Скачать руководство пользователя | Manualshive

Страница: 41 / 94

background image

Trawl Explorer | V5 | Sensor Configuration

Note:

On tablet computers,

Browse

only search for *.a1f files in the

Downloads

folder.

Information on the sensor firmware is displayed.

5.

Click

Apply

.

6.

Wait for the updating to be complete.

7.

Connect and disconnect the sensor to a charger to restart the sensor and validate the update.

Exporting Sensor Configuration Settings for Record Keeping

You can export in a *.txt file all the settings configured for the sensor (such as ping length,
frequency, range, TVG...).

Before you begin

• You have finished configuring the sensor.
• The sensor is connected to Mosa2.

About this task

The configuration file is a list displaying the firmware version, the board ID and all the settings
that can be configured via Mosa2. To check if settings have been set correctly, read sensor
configuration topics for guidelines on recommended values. Final lines called Pres coef correspond
to the depth coefficients uploaded in

Depth

settings. Other values listed that do not appear on

Mosa2 can be ignored.

Procedure

1.

Click the tab

Configuration

.

2.

Click

Configuration Output

.

3.

Click

Apply

under the black area.

The settings are displayed.

4.

To save the settings:

40

«
...
39
40
41
42
43
...
»

Содержание Trawl Explorer































































































Отзывы:

Нет отзывов

Похожие инструкции для Trawl Explorer

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: Camozzi Страницы: 2

Бренд: Oktober Страницы: 22

Бренд: Rainbow Страницы: 18

Бренд: Farmi Forest Corporation Страницы: 32

Бренд: Garmin Страницы: 12

Бренд: Garmin Страницы: 13

APT-9411 Series

Бренд: TAKAYA Страницы: 77

Бренд: Tadano Страницы: 402

Бренд: Wasp Страницы: 50

Бренд: Ultrasonic Страницы: 33

Бренд: Softing IT Networks Страницы: 54

Бренд: Velp Scientifica Страницы: 123

Бренд: IKA Страницы: 48

Бренд: ParaBody Страницы: 15

Бренд: ParaBody Страницы: 13

Бренд: Electro-Music Страницы: 120

Бренд: Yellowtec Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды