Marport Trawl Explorer Скачать руководство пользователя страница 29

Страница: 29 / 94

Trawl Explorer | V5 | Sensor Configuration

Before /

Turn 90° to the right /

After /

Card slot

Turn to 90° the transducer as shown on the picture.

With an Allen key, screw back the transducer.

Reconnect components.

Up & Down connectors /

Uplink

connector /

Uplink LED

Connect the uplink LED cable to the uplink
LED connector.

Connect the up (B), down (A) and uplink (C)
cables and add silicone glue.

Reconnect the batteries.

Tip:

If you have a doubt, the cable

types are written on them and their
location is written on the PCBA.

Put back into place the PCBA retainers and
screw with the 1.5 mm Allen key.

What to do next

You need to change the end cap orientation.

Changing the End Cap Orientation

Procedure

Remove the end cap.

Remove the four screws maintaining the end cap with the 1/8"
Allen key.

Содержание Trawl Explorer































































































Результаты поиска

Содержание Trawl Explorer

Отзывы:

Похожие инструкции для Trawl Explorer

Бренды по названию

Популярные бренды

Marport Trawl Explorer, Руководство по обслуживанию

Результаты поиска

Содержание Trawl Explorer

Отзывы:

Похожие инструкции для Trawl Explorer

Бренды по названию

Популярные бренды