Marport Trawl Explorer Скачать руководство пользователя страница 20

Страница: 20 / 94

Trawl Explorer | V5 | Sensor Configuration

Configuring the Uplink, Up and Down Settings

You can configure different settings for uplink, down and up soundings.

Before you begin

The sensor is connected to Mosa2.

About this task

Remember:

Always click

Apply

after you change a setting and make sure there is a green

check mark .

Procedure

Click the tab

Trawl Explorer

Uplink

Procedure

From

TE Uplink Frequency

, enter a frequency for the signal toward the vessel.

Important:

This parameter must be the same in the sensor settings in Scala/Scala2.

Up/Down Soundings

Procedure

From

NBTE Setup Options

, select the sounding mode (see

Sounding Modes

on page 18 for

more information).

From Down and Up

Sounding Range

, select the range according to how many meters you want

to see under the sensor.

Содержание Trawl Explorer































































































Результаты поиска

Содержание Trawl Explorer

Отзывы:

Похожие инструкции для Trawl Explorer

Бренды по названию

Популярные бренды

Marport Trawl Explorer, Руководство по обслуживанию

Результаты поиска

Содержание Trawl Explorer

Отзывы:

Похожие инструкции для Trawl Explorer

Бренды по названию

Популярные бренды