MARMON ANGELO PO COMBISTAR FX Скачать руководство пользователя страница 98

Страница: 98 / 178

Copyright by Servizio Clienti ANGELO PO Spa

4.4.4.

Adjustment during the test

4.4.4.1. Values of the minimum ignition failure:

Offset Adjust gas valve (PR.ADJ.)

If the combustion values at minimum power do not correspond

to the recommended offset adjusting of the valve is needed.

To do this with a screwdriver unscrew the protective brass cap

and take a 4mm Allen wrench.

At this point, if the CO2 is lower than the recommended value,

screw clockwise (see figure at right), to enrich the mixture.

If the CO2 is higher unscrew slowly to lessen the mixture.

The adjustment is very sensitive and you should make small movements (a quarter turn

rotation involves a variation of about 1% CO2) and wait for the gas analyzer to detect the

change and stabilize.

Once done repeat the wizard test.

When the adjustment is finished refit the protective cap of the screw.

Attention: the pressure adjustment screw PR.ADJ. has no effect on

increasing the power of the oven.

In case of change without written permission by Angelo Po, the

warranty will be void

Содержание ANGELO PO COMBISTAR FX



















































































































































































Результаты поиска

Содержание ANGELO PO COMBISTAR FX

Отзывы:

Похожие инструкции для ANGELO PO COMBISTAR FX

Бренды по названию

Популярные бренды

MARMON ANGELO PO COMBISTAR FX, Техническое руководство

Результаты поиска

Содержание ANGELO PO COMBISTAR FX

Отзывы:

Похожие инструкции для ANGELO PO COMBISTAR FX

Бренды по названию

Популярные бренды