manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 34

 

 

 

 

QUI-1122 

Page 34 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

 

 

5.3

 

System checkout  

 

With “Split On in Standby” selected of at least 20ml/min, ensure air/water background of MS is 
within operational limits. 

 

Confirm the calibration of any mass flow controllers is correct using a flow meter. 

 

If applicable, to checkout tube desorption mode, create a new TD- 2-3 stage desorb method using 
the parameters set out in documentation supplied with check standard QQR-0190. 

 

Using suitable GC(MS) parameters for the analysis of benzene, toluene, xylene, camphene and di-
octyl phthalate run the check standard. 

 

Assess the results, comparing against the example chromatogram. 

 

If the customer GC conditions prevent analysis of this standard (e.g. the wrong GC column is 
installed), or to check out on-line sampling mode, a customer standard should be run as an 
alternative 

 

Right click on the Instrument status and select ‘System Info’.  Create a copy of the calibration 
settings and record. 

 

Once all checks are complete, replace all covers. 

 

 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды