manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 32

 

 

 

 

QUI-1122 

Page 32 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

5.

 

Installation qualification 

5.1

 

Leak Testing  

 
Right-click on the Instrument Status Icon and select ‘Direct Control’.  
 

 

 
Load a tube into the tube oven and then click ‘Pressurise’ in the Manual Leak Test section. Once the 
pressure in the Markes TD status has stabilised, click ‘Leak Test’. Ensure the pressure does not fall at this 
stage to confirm the UNITY–Air Server-xr is leak tight. Should the pressure fall, then a leak checking 
procedure should commence using a helium leak detector to determine the source of the leak. Resolve 
and re-test. Once the instrument is demonstrated to be leak tight, the cold trap should be conditioned. 

5.2

 

Conditioning the cold trap 

CAUTION

:  

Do not exceed the cold trap temperature limits when conditioning the cold trap.  Refer to 
the Trap Certificate supplied with the cold trap to confirm the maximum temperatures.   

Click the Method Editor tile on the MIC home screen, open the Template Methods folder in the top left 
corner and choose the ‘TD-Trap Heat’ method to modify.  

 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды