Markem Imaje DigiConvert MC004-2014 P1082 Скачать руководство пользователя страница 62

Страница: 62 / 79

DigiConvert Operating Instructions

Copying this document, or disclosing it to third parties is not allowed without our approval. This document must not be used in any abusive way by the receiver or third
parties. Fe Vogt GmbH
DigiConvert Operating Instructions

62 of 79

11.3.2.

Main Menu

Touch the icon on the monitor in the machine overview to open a pop-up window in the right-hand
screen section.

Fig.: 22 Punching station

Here, the operator has the following possibilities:

•

Activating / deactivating the assembly

•

Applying the sheet

•

Drawing in the sheet

•

Locating the mark

•

Homing the axis

•

Performing first job presetting

•

Performing presetting

•

Switching on electrical shaft to the translative system

•

Entering the lead in [%]

•

Manual correction in [mm]

Содержание DigiConvert MC004-2014 P1082
















































































Результаты поиска

Содержание DigiConvert MC004-2014 P1082

Отзывы:

Markem Imaje DigiConvert MC004-2014 P1082, Руководство по эксплуатации, Страница: 62 / 79

Результаты поиска

Содержание DigiConvert MC004-2014 P1082

Отзывы: