manualshive.com logo in svg

Maretron MPOWER CLMD16, Руководство по настройке

Поделиться
Скачать
Maretron MPOWER CLMD16 Скачать руководство пользователя страница 23

____________________________________________________________ 

 

                                                    CLMD16 Configuration Guide Rev.1.1                                            19          

 

 

 

Toggle a Load On / Off from Multiple Momentary Input Sources Plus a  

“Toggle Network Input”  

 

Similar to toggling a load On / Off from multiple momentary input sources, this circuit type adds 
a “Toggling Network Input” signal into the circuit. When a CLMD16 ECB is in “Toggle Mode” 
the ECB will toggle the state from its 

current state of “On” or “Off” to the opposite state when 

the following occurs: The Rising Edge or “On” detection of an ECB “Toggle Network Input” or 
the Rising Edge or “On” detection of a direct ECB “Input Signal”. This operational mode will 
allow for a “Toggle Network Input” which could come from a third party MFD using 127500 
Load Controller PGN or any equipment running Maretron’s N2KView® software plus any 
applied direct ECB “Input Signal” to toggle the ECB in harmony with each other. Tip: When an 
ECB is in “Toggle Mode” a “Momentary Network Input” signal becomes unaffected by the 
“Toggle Mode”. 

In the following example, there will be two momentary input sources 

and one “Toggle Network 

Input” signal used to switch a single CLMD16 load in a Toggle fashion. One input is from a 
hardwired switch that has a momentary DC (-

) signal called “Binary Event Low” and one input 

is a momentary Discrete I/O input 

called “Discrete I/O 1”. There is the additional influence on 

the ECB of one externally set (Direct access through 127500 PGN

) “Toggle Network Input” 

signal. Take note that no different action is required to setup 

this circuit type than the “

Toggle a 

Load On / Off from Multiple Momentary Input Sources

”

 

circuit above. The only difference is the 

“Toggle Network Input” (shown in red) has access to the ECB setup by the message’s 
origination equipment, may it be a third party MFD using 127500 Load Controller PGN or any 
equipment running Maretr

on’s N2KView® software. Because the ECB is in “Toggle Mode” the 

ECB’s “Input Signal” and “Toggle Network Input” will work in harmony with each other toggling 
the ECB On / Off.  

Содержание MPOWER CLMD16



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды