background image

4

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries. 

cc))

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that
have the switch on invites accidents. 

d

d))

Remove any adjusting key or wrench before turning the power tool on. A wrench

or a key left attached to a rotating part of the power tool may result in personal
injury. 

e

e))

Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations.

ff))

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.

g

g))

If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust-related hazards.

4

4)) P

Po

ow

we

err  tto

oo

oll  u

usse

e  a

an

nd

d  cca

arre

e

a

a))

Do not force the power tool. Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it was
designed. 

b

b))

Do not use the power tool if the switch does not turn it on and off. Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

cc))

Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of starting the power tool
accidentally. 

d

d))

Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users. 

e

e))

Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.

ff))

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control. 

g

g))

Use the power tool, accessories and tool bits etc. in accordance with these

instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation. 

5

5)) S

Se

errv

viicce

e

a

a))

Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Содержание DDM2

















Отзывы: