ENGLISH
MANUAL
UNIT APPEARANCE
GETTING STARTED
ALARM FUNCTION
MANUAL SETTINGS
A1
Radio control icon
A2
Time zone
A3
Time display
A4
Day of the week
A5
Temperature
B6
Date
B7
Humidity
B1
H
/ TIME ZONE button
B2
AL ON/OFF button
C3
Stand
B3
MODE/SET button
B4
(°C/°F) button
B5
I
/
J
button
B6
12/24 button
B7
RESET button
C1
Wall mounting hole
C2
Battery compartment
HOLD 3 SEC TO TURN
WAVE “ON” OR “OFF”
C1
B1
B2
B7
C2
B6
C3
A1
A2
A7
B4
A3
A4
A5
A6
B3
B5
SUPER JUMBO ATOMIC FULL CALENDAR CLOCK WITH 7 TIME
ZONES, EXTRA LARGE DIGITS, TEMPERATURE AND HUMIDITY
MODEL CL030061-FD SERIES
• Radio-controlled time (RC-WWVB)
• Time display in 12-hour or 24-hour format
• Daily alarm function
• Perpetual calendar to year 2099
• Day of the week in one of three languages
• Temperature display in Celsius or Fahrenheit
SECTION 1
SECTION 2
1. Open the battery compartment cover
(C2)
.
2. Insert three C batteries, following the polarity marks
(+)
and
(-)
.
3. Replace the battery compartment cover
(C2)
.
SECTION 3
After the batteries are inserted, the clock will automatically start to
search for the WWVB time signal. The radio control icon
J
(A1)
will
•
The clock automatically searches for the time signal at 2:00 a.m.
every day to maintain accurate time. If the reception fails, the
scanning will stop and the icon
J
(A1)
will disappear from the
display.
•
The clock can be set to search for the time signal manually by
pressing and holding the
J
button
(B5)
for three seconds. Each
•
The scanning can be stopped by pressing and holding the
J
button
(B5)
for three seconds.
•
To select the time zone, set the RCC function to ON in setting
mode, then press and hold the
▲/TIME ZONE
button (B1).
•
There are seven time zones to choose from:
Alaskan – AK,
or
Hawaii – H.
For information about WWVB, visit
www.nist.gov/pml/div688/grp40/wwvb.cfm.
•
The icon will be visible on the display if Daylight Saving Time
has been activated
(B7)
.
SECTION 4
•
In time display mode, press and hold the
MODE
button (B3) for
three seconds to enter the Clock/Calendar setting mode.
•
The setting sequence is as follows:
12/24-hour, RCC ON/OFF,
Time zone, Weekday language, Hour, Minutes, Seconds, Year,
Month, Date, DST ON/OFF,
Temperature units and Alarm duration.
•
Press the ▲
(B1)
or the ▼
(B5)
button to adjust the values, then
press the
MODE
button
(B3)
•
(By pressing and holding the ▲
(B1
) or the ▼
(B5)
button, the
process can be accelerated to reach the desired value faster.)
•
To display the time in 12-hour or 24-hour format, press the 12/24
button
(B6
).
•
The day of the week and the month can be displayed in one of
three languages: English, French or Spanish.
Note:
1. The clock will automatically exit the setting mode after 15 seconds
if no button is pressed.
2. Alarm sound duration: there are two options available, “1 minute”
and “2 minutes”.
3. The seconds can only be adjusted to 0.
4. If the area can receive the WWVB signal, and if both the RCC
function and the DST function are ON,
N
will be visible on
the display during Daylight Saving Time.
SECTION 5
•
Press the MODE button
(B3)
to select the alarm time. ALARM
•
While viewing the alarm time, press and hold the MODE button
(B3) for three seconds to enter the alarm time setting mode. Press
the ▲
(B1)
or the ▼
(B5)
button to set the alarm time. Press the
MODE button
(B3)
1
J
FLASHES,
indicating signal
reception in progress.
J
STAYS ON,
indicating successful
signal reception.
J
DISAPPEARS,
indicating failure of
signal reception.
