Marantz ND8006 Скачать руководство пользователя страница 79

Страница: 79 / 85

3. Update method when the DIGITAL PCB or network module is replaced (Using a USB flash drive U1004, U3001, NETWORK MODULE)

3.1. File structure on USB flash drive

DIGITAL PCB or network module is replaced onto the USB flash drive in the following structure.

After unzipping the files, store them in the root of the same USB flash drive.

Model Area

Download from SDI

ALL

avr_40.prod.update.factory.xxxx.zip

USB flash drive root

  + avr_40.prod.update.factory
    + xxxxxxzz.ota-download
    + heos_40.prod.update.factory

    xxxxxx :  Model name
    zz :      Region

3.2. Start the update.

NOTE :

• Remove the LAN cable from this unit when updating.

(Do not connect to a wired or wireless network.)

• The GUI menu setting details and image quality adjustment setting details are initialized when

Firmware Factory Restore is performed. Therefore, take a note of the setting details beforehand and

reconfigure the settings after update.

(1) Press the power button to turn on the power.

(2) Wait for this unit to start up.

(3) Set the input source to Internet Radio.

Check that the display is as shown below.

(4) Insert the USB flash drive into the USB port.

Download ﬁrmware

in USB ﬂash drive.

(5) USB Update starts automatically.

The Standby LED lights red.

Display during USB update

↓

It takes a maximum of approximately 11 minutes for update to complete.

(6) The unit restarts when update is complete.

When update is complete, the folder name on the USB flash drive changes to "

avr_40.prod.update.factory

done

". To use the files again, delete the "

.done

" part.

(7) Execute Firmware Factory Restore.

Insert the AC plug while pressing buttons "

POWER

" and "

BACK

" together, and wait for more than 3

seconds.

Display during Firmware Factory Restore

The "

DISPLAY OFF

" and "

DIG. OUT OFF

" LED indicator lights red.

↓

It takes approximately 7 minutes for Firmware Factory Restore to complete.

(8) Execute Service Region Settings.

See "

4. Update Method for Service Region Settings (U1004, U3001, NETWORK MODULE)

(9) Check that the version is the specified version. See "

1-1. Version Display Mode

(10) OTA or the USB flash drive to update the firmware to the newest version.

We recommend using the firmware update method using OTA.

See "

5. Normal Firmware Update Method from USB Flash Drive (U1004, U3001, NETWORK MODULE)

or "

6. Normal Firmware Update Method from OTA (U1004, U3001, NETWORK MODULE)

---Cautions on Firmware Update---

• Do not remove the USB flash drive until updating is completed.

• Do not turn off the power until updating is completed.

• It takes a maximum of approximately 25 minutes for update to complete.

Once an update is started, normal operations cannot be performed until it is completed.

Before Servicing

This Unit

Electrical

Mechanical

Repair Information

Updating

Содержание ND8006





















































































Результаты поиска

Содержание ND8006

Отзывы:

Похожие инструкции для ND8006

Бренды по названию

Популярные бренды

Marantz ND8006, Руководство по обслуживанию

Результаты поиска

Содержание ND8006

Отзывы:

Похожие инструкции для ND8006

Бренды по названию

Популярные бренды