background image

15

WARNING

AVOID ACCIDENTAL BLADE

ENGAGEMENT

DO NOT SQUEEZE THE THROTTLE

TRIGGER WHEN STARTING.

MAINTAIN PROPER IDLE SPEED

ADJUSTMENT (2500-3100 RPM)

TO START YOUR
TILLER FOR THE
FIRST TIME:

First, fill the fuel tank with the
proper amount of gasoline (Use
branded 89 octane  (R+M+2)
unleaded gasoline or gasohol—
maximum 10% ethyl alcohol, or
15% MTBE, no methyl alcohol.) 

Mantis Tiller Starting
Instructions

(4 Stroke 25cc engine)

Cold Engine

1. Place the 

o/

I

switch into the 

I

“start/on” position. (Picture 1)

2. Choke the engine (or close
the choke. Move choke up to the
closed position.) (Picture 2) 
3. Push primer bulb 6 times.
(Picture 3)

4. Pull grip slowly until you feel
resistance then pull briskly.
(Picture 4)

5. Once the engine is running,
slowly push the choke lever

down to the run position—the
engine will continue to run.
(Picture 5)

Warm Engine

1. Push ignition switch to 

I

“start/on” position.

2. Pull grip slowly until you feel
resistance then pull briskly.
Make sure the choke is in the
open, or run, position.

NOTE: When the choke is
closed, never pull the cord more
than four or five times. Over-
pulling may cause flooding. 

Follow these steps whenever you
are starting the engine “cold”, or
when the engine has run dry and
you have just added fuel.
Remember, always use short,
brisk pulls. Don’t give the cord
a long, forceful yank. And, do
not let the cord snap back into
the starter housing.

Picture 4

Picture 5

Picture 6

Picture 1

Picture 2

Picture 3

Starting

!

!

How to Stop the Engine

    Simply push the 

o/

I

“stop/ start”

switch to “

o

” (Picture 6). This will

stop the engine instantly. If it
should ever fail to do so, just pull
the choke up to the closed position.
The engine will stop at once.

About the Choke

    The choke controls the amount of

air drawn into the engine. Your tiller
will run only if the choke is open.

IMPORTANT!

It is normal for your 
4 stroke engine to smoke for 
the first minute or two of
operation, however it is not
necessary for this to occur
every time. This is a result of
the oil being pulled through
the engine for lubrication.

WARNING • DANGER

IF ENGINE DOES NOT STOP WHEN SWITCH IS PUT IN THE STOP

POSITION, RELEASE THE THROTTLE, ALLOW ENGINE TO IDLE, PUT THE

TILLER DOWN AND PULL THE CHOKE BUTTON OUT TO SHUT ENGINE

DOWN. HAVE PRODUCT SERVICED BEFORE USING.

!

!

401777 Deluxe 4C Tiller-Cultivator_400752.Tiller/Cultivator  8/12/11  10:53 AM  Page 15

Содержание DELUXE 7264

























Отзывы: