Man E 0824 E 301 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 48

Man E 0824 E 301 Скачать руководство пользователя страница 25

Maintenance and care

23

Refilling with oil

Caution:
Do not add so much engine oil that
the oil level rises above the max.
marking on the dipstick. Overfilling will
result in damage to the engine.

Fill up with fresh engine oil via oil filler
neck on cylinder head cover.

After the filling operation start engine, let it
idle for a few minutes and then check oil
pressure and for leaks.
Switch off engine and check oil level after
five minutes.

D

Pull out dipstick

D

wipe it with a clean, lintfree cloth

D

and push it in again up to the stop

D

Pull out dipstick again

The oil level should be between the two
notches in the dipstick and must never fall
below the lower notch. Top up oil as
necessary.

MIN

MAX

Oil

?

MIN

MAX

Note:
Use only approved engine oils for natural-gas engines (see “Fuels, Lubricants and
Coolants for Industrial Gas Engines”); non-compliance renders warranty claims
against manufacturer null and void.

«
...
23
24
25
26
27
...
»

Содержание E 0824 E 301

















































Отзывы:

Нет отзывов