manualshive.com logo in svg

Man E 0824 E 301, Руководство по эксплуатации, Страница: 18 / 48

Поделиться
Скачать
Man E 0824 E 301 Скачать руководство пользователя страница 18

Commissioning and operation

16

First commissioning

Filling-in of coolant

Fill the cooling system of the engine with a mixture of drinkable tap water and anti-freeze
agent on ethylene glycole basis or anti-corrosion agent (see “Fuels, Lubricants and Cool-
ants for MAN Industrial Gas Engines”).

D

Comply with the filling instructions of the cogeneration–plant manufacturer

D

Slowly fill up with coolant (max. 10 l/min.)

Filling with engine oil

Caution:
Do not add so much engine oil that the oil level rises above the max. marking on the
dipstick. Overfilling will result in damage to the engine.

The engines are as a rule supplied with-
out oil.

Pour oil into engine via filler neck.

For the quantity required see “Technical
Data”.

Note:
Use approved service products only (see “Fuels, Lubricants and Coolants for MAN
Industrial Gas Engines”); non-compliance renders warranty claims against manufac-
turer null and void.

Ensure outmost cleanliness when handling lubricants and coolants.

Содержание E 0824 E 301

















































Отзывы:

Нет отзывов