Man E 0824 E 301 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 48

Man E 0824 E 301 Скачать руководство пользователя страница 12

Safety regulations

10

3. Regulations designed to prevent pollution

Engine oil and filter elements / cartridges, fuel / fuel filter

D

Take old oil only to an old oil collection point.

D

Take strict precautions to ensure that no oil or Diesel fuel gets into the drains or the
ground.
The drinking water supply could be contaminated.

D

Filter elements are classed as dangerous waste and must be treated as such.

Coolant

D

Treat undiluted anti-corrosion agent and / or anti-freeze as dangerous waste.

D

When disposing of spent coolant comply with the regulations of the relevant local au-
thorities.

4. Notes on safety in handling used engine oil

∗

Prolonged or repeated contact between the skin and any kind of engine oil decreases the
skin. Drying, irritation or inflammation of the skin may therefore occur. Used engine oil
also contains dangerous substances which have caused skin cancer in animal experi-
ments. If the basic rules of hygiene and health and safety at work are observed, health
risks are not to the expected as a result of handling used engine oil.

Health precautions:

D

Avoid prolonged or repeated skin contact with used engine oil.

D

Protect your skin by means of suitable agents (creams etc.) or wear protective gloves.

D

Clean skin which has been in contact with engine oil.
– Wash thoroughly with soap and water. A nailbrush is an effective aid.
– Certain products make it easier to clean your hands.
– Do not use petrol, Diesel fuel, gas oil, thinners or solvents as washing agents.

D

After washing apply a fatty skin cream to the skin.

D

Change oil-soaked clothing and shoes.

D

Do not put oily rags into your pockets.

«
...
10
11
12
13
14
...
»

Содержание E 0824 E 301

















































Отзывы:

Нет отзывов