Man D2842 LE103 Скачать руководство пользователя страница 22

Страница: 22 / 90

General Safety Instructions

MAN-Industrial diesel engines D2842 LE103

Carefully read the Operating Instructions before starting any work!

This is especially valid for the chapter on General Safety Instructions

and the safety instructions in each of the chapters.

2.10 Signs

The following symbols should be installed in the immediate vicinity of the hazard area.

WARNING!

Risk of injury caused by illegible symbols!

In the course of time, stickers and symbols become dirty or unrecognisable for other reas
ons!

For this reason:

Always keep the safety, warning and operational signs in good legible condition.

Clean or replace illegible safety, warning and operational signs.

Electric Voltage

Rooms marked with this symbol may only be accessed by qualified electricians.

Unauthorised persons may not enter these rooms.

Hot Surfaces

Hot surfaces such as hot engines and hot fluids may not always be recognisable. Do not
touch these surfaces without protective gloves.

Содержание D2842 LE103



























































































Результаты поиска

Содержание D2842 LE103

Отзывы:

Бренды по названию

Популярные бренды

Man D2842 LE103, Руководство по эксплуатации

Результаты поиска

Содержание D2842 LE103

Отзывы:

Бренды по названию

Популярные бренды