Man D 0836 LE 401 Скачать руководство пользователя страница 55

Страница: 55 / 76

Commissioning and operation

Terminal box in the engine room / interface with light-emitting keys

The terminal box with light-emitting diodes functions at the same time as an engine room
monitoring panel.

If an alarm is issued, the corresponding light-emitting diode lights up. The following re-
lays are activated on the diagnosis unit:

Engine slow down (main alarm) = reduction of engine speed

Horn = acoustic alarm

Group alarm = collective fault indication

The keys are intended for:

Horn off

Switches off the alarm horn and the integrated buzzer

Flashing light off, transition to continuous light / test of light-emitting diodes

Switches off the flashing signal of the relevant warning lamp, i.e. the flashing
light switches to continuous light. Before the flashing signal is cleared, the
alarm horn must be switched off

Reset

Clears the alarm message (red warning lamp goes out)

Requirement for clearing an alarm message is:

−

Pressing the keys “Horn off” and “Test” in that order

−

Removing the cause of the alarm

−

In the case of an engine slow down alarm, short-term lowering of engine
speed below 800 rpm so that higher engine speed can be reached

−

In the case of a stop alarm, the alarm can only be deleted if the engine is at
a standstill

Содержание D 0836 LE 401













































































Результаты поиска

Содержание D 0836 LE 401

Отзывы:

Бренды по названию

Популярные бренды

Man D 0836 LE 401, Руководство по эксплуатации

Результаты поиска

Содержание D 0836 LE 401

Отзывы:

Бренды по названию

Популярные бренды