8
19.
Be careful not to damage the spindle, the
flange (especially the installing surface) or the
lock nut. Damage to these parts could result
in wheel breakage.
20.
Make sure the wheel is not contacting the
workpiece before the switch is turned on.
21.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced wheel.
22.
Use the specified surface of the wheel to
perform the grinding.
23.
Do not leave the tool running. Operate the tool
only when hand-held.
24.
Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
25.
Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care.
26.
Do not use separate reducing bushings or
adaptors to adapt large hole abrasive wheels.
27.
Use only flanges specified for this tool.
28.
For tools intended to be fitted with threaded
hole wheel, ensure that the thread in the
wheel is long enough to accept the spindle
length.
29.
Check that the workpiece is properly
supported.
30.
Pay attention that the wheel continues to
rotate after the tool is switched off.
31.
If working place is extremely hot and humid,
or badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure
operator safety.
32.
Do not use the tool on any materials
containing asbestos.
33.
When use cut-off wheel, always work with the
dust collecting wheel guard required by
domestic regulation.
34.
Cutting discs must not be subjected to any
lateral pressure.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
FUNCTIONAL DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before adjusting or checking function
on the tool.
Shaft lock
Fig.1
CAUTION:
•
Never actuate the shaft lock when the spindle is
moving. The tool may be damaged.
Press the shaft lock to prevent spindle rotation when
installing or removing accessories.
Switch handle mounting positions
Fig.2
The switch handle can be rotated to either 90° left or
right to fit your work needs. First, unplug the tool. Press
the lock button and rotate the switch handle to left or
right fully. The switch handle will be locked in that
position.
CAUTION:
•
Always make sure that the switch handle is locked
in the desired position before operation.
Switch action
CAUTION:
•
Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
•
Switch can be locked in "ON" position for ease of
operator comfort during extended use. Apply
caution when locking tool in "ON" position and
maintain firm grasp on tool.
Fig.3
For tool with the lock-on switch
To start the tool, simply pull the switch trigger (in the B
direction). Release the switch trigger to stop. For
continuous operation, pull the switch trigger (in the B
direction) and then push in the lock lever (in the A
direction). To stop the tool from the locked position, pull
the switch trigger fully (in the B direction), then release it.
For tool with the lock-off switch
To prevent the switch trigger from accidentally pulled, a
lock lever is provided.
To start the tool, push in the lock lever (in the A
direction) and then pull the switch trigger (in the B
direction). Release the switch trigger to stop.
For tool with the lock on and lock-off switch
To prevent the switch trigger from accidentally pulled, a
lock lever is provided.
To start the tool, push in the lock lever (in the A
direction) and then pull the switch trigger (in the B
direction). Release the switch trigger to stop.
Содержание GA7030
Страница 81: ...81 ...
Страница 82: ...82 ...
Страница 83: ...83 ...
Страница 84: ...84 Makita Corporation Anjo Aichi Japan www makita com 884649F975 ...