22 ENGLISH
Hex wrench storage
CAUTION:
Be careful not to leave the hex
wrench inserted in the tool head.
It may cause
injury and/or damage to the tool.
When not in use, store the hex wrench as illustrated to
keep it from being lost.
►
Fig.17:
1.
Hex wrench
For the loop handle model, the hex wrench can also be
stored on the handle as illustrated.
►
Fig.18:
1.
Hex wrench
Correct combination of the cutting
tool and the protector
CAUTION:
Always use the correct combi
-
nation of cutting tool and the protector.
A wrong
combination may not protect you from the cutting tool,
flying debris, and stones. It can also affect the bal
-
ance of the tool and result in an injury.
Cutting tool
Protector
Cutter blade
(3-tooth, 4-tooth, and 8-tooth
blades)
Nylon cutting head
Plastic blade
Installing the protector
WARNING:
Never use the tool without the
guard illustrated in place.
Failure to do so can
cause serious personal injury.
NOTE:
The type of the protector supplied as the stan-
dard accessory varies depending on the countries.
For cutter blade
Attach the protector to the clamp using bolts.
►
Fig.19:
1.
Clamp
2.
Protector
For nylon cutting head / plastic blade
CAUTION:
Take care not to injure yourself on
the cutter for cutting the nylon cord.
Attach the protector to the clamp using bolts.
►
Fig.20:
1.
Clamp
2.
Protector
3.
Cutter
Installing the cutting tool
CAUTION:
Always use the supplied
wrench(es) to remove or to install the cutting tool.
CAUTION:
Be sure to remove the hex wrench
inserted into the tool head after installing the
cutting tool.
NOTE:
The type of the cutting tool(s) supplied as the
standard accessory varies depending on the coun-
tires. The cutting tool is not included in some specifi
-
cations of the model.
NOTE:
Turn the tool upside down so that you can
replace the cutting tool easily.
Cutter blade
CAUTION:
When handling the cutter blade, always
wear gloves and put the blade cover on the blade.
CAUTION:
The cutter blade must be well polished,
and free of cracks or breakage.
If the cutter blade hits a stone
during operation, stop the tool and check the blade immediately.
CAUTION:
The cutter blade-fastening nut
(with spring washer) wears out in course of time.
If there appears any wear or deformation on the
spring washer, replace the nut. Ask your local
authorized service center to order it.
CAUTION:
The outside diameter of the cutter
blade must be as follows. Never use any cutter
blade with larger outside diameter.
— 3-tooth blade : 230 mm
— 4-tooth blade : 230 mm
— 8-tooth blade : 230 mm
►
Fig.21:
1.
Nut
2.
Cup
3.
Clamp washer
4.
Cutter
blade
5.
Spindle
6.
Receive washer
7.
Hex
wrench
1.
Insert the hex wrench through the hole in the tool
head to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
2.
Mount the cutter blade onto the receive washer so
that the arrows on the blade and protector are pointing
in the same direction.
►
Fig.22:
1.
Arrow
3.
Put the clamp washer and cup onto the cutter blade
and then tighten the nut securely by the box wrench.
►
Fig.23:
1.
Tighten
2.
Loosen
3.
Box wrench
4.
Cup
5.
Hex wrench
NOTE:
Tightening torque : 16 - 23 N•m
4.
Remove the hex wrench from the tool head.
To remove the cutter blade, follow the installation proce-
dures in reverse.
Содержание 10181717
