12 ENGLISH
NOTE:
The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE:
The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The following table shows the vibration total value
(tri-axial vector sum) determined according to applica-
ble standard.
Work mode
Vibration
emission
Uncertainty (K) Applicable
standard /
Test condition
Hammer
drilling into
concrete
(a
h, HD
)
10.4 m/s
2
1.5 m/s
2
EN62841-2-6
9.2 m/s
2
1.5 m/s
2
Recommended
practical
operation*
Hammer
drilling into
concrete with
DX15 (a
h, HD
)
8.1 m/s
2
1.5 m/s
2
EN62841-2-6
6.7 m/s
2
1.5 m/s
2
Recommended
practical
operation*
Chiselling
(a
h, CHeq
)
9.7 m/s
2
1.5 m/s
2
EN62841-2-6
9.1 m/s
2
1.5 m/s
2
Recommended
practical
operation*
* The test condition of recommended practical operation
meets EN 62841-2-6, except for the following points:
•
Feed force is applied to the switch handle (main
handle) for working accuracy and efficiency.
•
The side grip/handle (auxiliary handle) is held to
keep balance of the tool.
NOTE:
The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool.
Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
CORDLESS ROTARY HAMMER
SAFETY WARNINGS
Safety instructions for all operations
1.
Wear ear protectors.
Exposure to noise can
cause hearing loss.
2.
Use auxiliary handle(s), if supplied with the
tool.
Loss of control can cause personal injury.
3.
Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring.
Cutting accessory contacting a "live"
wire may make exposed metal parts of the power
tool "live" and could give the operator an electric
shock.
Safety instructions when using long drill bits with
rotary hammers
1.
Always start drilling at low speed and with the
bit tip in contact with the workpiece.
At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting
in personal injury.
Содержание 0088381754781
