MAKINEX DPW-4000-VS Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 47

MAKINEX DPW-4000-VS Скачать руководство пользователя страница 31

Page 28 of 44

CHECK SPRAY GUN

Examine the hose connection to the spray gun and make sure it is secure, and
make sure

the ‘safety lock’ is present and attach on the trigger, it helps to prevent

any accidental jets when in operation. Replace spray gun immediately if the safety
lock is damaged or not functioning.

CHECK WAND

Occasionally,  the  spray  wand  can be  clogged  with  foreign materials  such as  dirt.
When  this  happens,  excessive  pressure  can  develop.  Whenever  the  pressure
nozzle  becomes  partially  clogged,  the  pump  pressure  will  pulsate.  It  should  be
cleaned immediately cleaned.

NOZZLE MAINTENANCE

A pulsing sensation felt  while squeezing the spray gun trigger may be caused by
excessive  pump  pressure.  The  principal  cause  of  excessive  pump  pressure  is  a
spray tip clogged or restricted with foreign materials, such as dirt,  etc. To  correct
the problem, immediately clean the spray tip following these instructions:

1.

Shut off engine and turn off water supply.

2.

ALWAYS point spray gun in safe direction, squeeze spray gun trigger to
release retained high water pressure.

3.

Remove spray tip from end of nozzle extension.

4.

Use a small paper clip to free any foreign material clogging or restricting
spray tip of the nozzle.

5.

Remove nozzle extension from spray gun.

6.

Using a garden hose, remove additional debris by back flushing water
through the nozzle extension.

7.

Reinstall spray tip into nozzle extension.

8.

Reconnect nozzle extension to spray gun.

9.

Make sure garden hose is connected to spray gun and pump. Turn on water.

10. Start engin

e following instructions ‘How to Start Your Pressure Washer’.

11. Test pressure washer by operating the spray gun

12. Use same nozzle maintenance with the Surface-Cleaner.

If  pressure  drops  off  check  nozzle  for  wear.  Nozzles  should  be  replaced  on  a
regular  basis  (suggestion:  every  month  for  machines  in  regular  use,  every  three
months  for  machines  used  intermittently).  Using  the  machine  with  the  incorrect
nozzle  size  or  worn  nozzle  will

VOID WARRANTY

and can be

DANGEROUS

to

operator.

«
...
29
30
31
32
33
...
»

Содержание DPW-4000-VS
















































Отзывы:

Нет отзывов