MAKINEX DPW-4000-VS Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 47

MAKINEX DPW-4000-VS Скачать руководство пользователя страница 26

Page 23 of 44

8. NOZZLE SELECTION

The nozzle on the spray gun that comes with the MAKINEX dual pressure washer
are 15°, 25°, and 40° Quick Connect nozzles.

Your Surface-Cleaner will come installed with one set of 25015 nozzles (25-degree
1.5 orifice).

The minimum orifice to be used in your Surface-Cleaner is half that which is being
used in your pressure washer. Example: If your pressure washer uses a size 5
orifice, you need to use a size 2.5 orifice in your Surface-Cleaner.

The nozzles being used should have a 15° -25° spray pattern; anything less than a
15° spray pattern can damage the area being cleaned. Anything more than 25° may
not allow the bar to rotate.

Nozzles should be screwed into the rotating bar. The spray fan should be parallel to
the rotating bar.

NOTE

: The Dual Pressure Washer (DPW-4000-VS) only comes with one nozzle therefore

there is not a selection to choose from.

NOTE:

Wand nozzle leaks can be caused by

damaged or missing O-ring/Seal inside the quick
connect fitting. If leaks occur, please replace
before operation

«
...
24
25
26
27
28
...
»

Содержание DPW-4000-VS
















































Отзывы:

Нет отзывов