MAINLINE Kleiss MCS60-38 страница 9 Скачать руководство пользователя | Manualshive

Страница: 9 / 49

background image

8

Kleiss MCS60-38 System Manual v.15 May 2020

|

www.MainlineControlSystems.com

Example II – Stopper Retraction Sequence: Stoppers Positioned Away From Work Area

Example II – Stopper Retraction Sequence: Stoppers Positioned Away From Work Area

NOTE: Always equalize pressure on both sides of the stopper before deflation or removal.

1)

Deflate stopper #2.

2) Back pressure stopper #4 through the system pressure ports in towers #3 and #4.

3) Deflate stopper #4.

4) Equalize pressure on stoppers #1 and #3 through the by-pass / vent port between towers #3 and #4.

5) Use the by-pass / vent port in tower #1 or #2 to purge air from repaired area.

6) Use system pressure gauge on tower #1 or #2 to determine stoppers are equalized.

7)

Deflate and remove stoppers.

8) Remove tools and install completion plugs.

NOTE: For additional set up illustrations, see Appendix B.

«
...
7
8
9
10
11
...
»

Содержание Kleiss MCS60-38


















































Отзывы:

Нет отзывов

Похожие инструкции для Kleiss MCS60-38

Бренд: Waterwise Страницы: 12

Бренд: ParaBody Страницы: 38

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: Gaspardo Страницы: 196

Бренд: RAB Страницы: 2

Бренд: U-Line Страницы: 3

Бренд: U-Line Страницы: 2

Sonorex Super RK 31

Бренд: BANDELIN Страницы: 21

BTL7-A/E501-M Series

Бренд: Balluff Страницы: 194

Бренд: B.Pro Страницы: 48

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 2

Бренд: Bayer HealthCare Страницы: 104

EDC2-1001-RGB-MWT

Бренд: Energizer Страницы: 18

Бренд: MIETHKE Страницы: 125

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды