MAINLINE Kleiss MCS60-38 страница 41 Скачать руководство пользователя

Страница: 41 / 49

Kleiss MCS60-38 System Manual v.15 May 2020

www.MainlineControlSystems.com

10.0 General Maintenance:

All equipment should be cleaned and inspected for wear after each job

to prolong the life of the equipment and ensure the safety of the operators.



Inventory all system components (refer to Section 4.0 Equipment)



Visually inspect the cutters and pilot drills



PE cutter - no missing or chipped teeth (13100080)



Steel and cast iron cutter - looks to be in good condition (13200140)



Pilot drill - looks to be in good condition (14300060)



NOTE: The best indication of the condition of the cutter and pilot drill is the coupon removed from the pipe.

Smooth cuts indicate good condition and jagged / rough cuts indicate wear of the cutter and pilot drill.



Grease the tapping device, if needed (10310800)



Inspect gauges for any damage and ensure they are reading zero and function properly



Inspect stopper rod for bends and/or damage



Check to make sure the gear box is operating freely with no binding or grinding



Clean ALL threads and quick connections



Inspect and clean all chutes (quantity 2)



Inspect to make sure ball valve is opening and closing smoothly and functioning properly



Inspect all bolts, screws, and joints



Inspect MDS Stoppers for any excessive wear and replace if necessary (refer to Appendix A)



Make sure protective cap is on the stopper to protect the threads



Thoroughly clean off any dirt, debris, and grease on all tools and stoppers with a lint free cloth and water

(well-maintained equipment extends the life)

NOTE: MCS recommends that the complete set of tools be inspected, serviced, and tested by an authorized MCS

service center on a two year rotation or sooner.

Содержание Kleiss MCS60-38


















































Результаты поиска

Содержание Kleiss MCS60-38

Отзывы:

Похожие инструкции для Kleiss MCS60-38

Бренды по названию

Популярные бренды

MAINLINE Kleiss MCS60-38, Руководство пользователя

Результаты поиска

Содержание Kleiss MCS60-38

Отзывы:

Похожие инструкции для Kleiss MCS60-38

Бренды по названию

Популярные бренды