background image

 INSTRUCTION MANUAL FOR DISHWASHERS

 

 

 

Page 11 of 12 

 

UK 

Chap 7

 

SETTINGS 

 

 

The following settings should only be configured by a qualified technician. 

The parameters listed below can be set during installation of afterwards, accessing the settings menu as 
follows: 

  Machine in standby with door open. 

  Press buttons 2 and 3 together (cycle selection and 

START

) for 5 seconds and enter the key 

CH 12

 

(buttons 2 and 3 to change the parameter, 1 to confirm). 

  Then press button 1 (

ON/OFF

) repeatedly to scroll through the following headings, enabling and/or 

changing them using buttons 2 and 3 (the modified parameter is memorised without being 
confirmed). The list of parameters may vary according to the type of dishwasher. 

 

Language

 

Language selection 

 

Boiler 

Temperature

 

Boiler temperature settings for programmes. In the versions with 
atmospheric boiler (rinse pump) there are different settings for each 
programme (b1 – b2 – b3) 

 

Tank  

Temperature

 

Tub temperature regulation for programmes. Rinse pump versions have 
different settings for each programme (t1 – t2 – t3) 

 

Thermo - Stop

 

Enabling the Thermostop function, which guarantees the correct 
rinse temperature. 

 

Energy  

Saving

 

Enabling the Energy Saving function, which guarantees  
energy savings when the dishwasher is on but not in use. 

 

Detergent  

Pump

 

Manual operation of detergent doser 

 

Rinse Aid  

Pump

 

Manual operation of rinse aid doser 

 

Manual 

Rinse

 

Manual operation of the rinse pump 

 

Dosage 

Detergent

 

Detergent dosing time

 

Dosage  

Rinse Aid

 

Rinse aid dosing time 

 

Water 

Hardness

 

Setting the supply water hardness (dishwashers with water softener): enter 
the values given in the table below 

 

Set Number 

Service Cycles

 

Setting and enabling the cycle counter to enable the servicing warning 

 

Autostart 

Autoenabling

 

Automatic enabling of automatic starting 

 

Cycle Counter

 

Cycle counter 

Once all necessary parameters have been set, to exit and memorise any changes simply press and 
hold button 1 for a few seconds until the on-line dashes appear. 

 
 

Содержание c451














Отзывы: