Maico ER GH страница 27 Скачать руководство пользователя

Страница: 27 / 32

14. ER-AS extraction socket for WC odour extraction

14. ER-AS extraction socket for

WC odour extraction

ER GH housings can be connected to the

WC flushing pipe using the ER-AS extraction

socket.
A Ø 70 duct cross section facilitates low air

speeds in the connecting duct and an

effective, draft-free extraction of odours.

Pre-requirement for the connection:

A Ø 70 branch must be installed in the

flushing pipe of the concealed cistern.

Installation

1. Install ER-AS extraction socket as

described in chapter 11.1.6.

2. Connect the connection duct to the ER-AS

extraction socket and (at the branching

piece) to the concealed cistern’s flushing

pipe. Make sure the connections between

the connection duct and the ER-AS

extraction socket and the branch are tight.

3. For the assembly of fan inserts and covers



ER cover manual.

15. Spare parts

Spare parts may only be sourced

from and fitted by a specialist

installer.

Designation

Article no.

Exhaust socket

0059.2046.0000

Shutter

E093.0608.0001

Exhaust element

on side

0059.2053.0000

Exhaust element

at rear

0059.2054.0000

In case of questions, please contact:

Maico Elektroapparate-Fabrik GmbH

Steinbeisstraße 20

78056 Villingen-Schwenningen

Germany

Tel. +49 7720 694 445

Fax +49 7720 694 175

E-mail: [email protected]

Содержание ER GH

































Результаты поиска

Содержание ER GH

Отзывы:

Похожие инструкции для ER GH

Бренды по названию

Популярные бренды

Maico ER GH, Инструкция по монтажу

Результаты поиска

Содержание ER GH

Отзывы:

Похожие инструкции для ER GH

Бренды по названию

Популярные бренды