Maico ER GH страница 24 Скачать руководство пользователя | Manualshive

Страница: 24 / 32

background image

12. Electrical connection

24

12. Electrical connection

16  Power cable
32  Stepped grommet
34  Terminal block

CAUTION

Risk of damage to unit in the event of

short-circuits.

Cut off and insulate PE

conductor and individual cable cores that

are not required!

NOTICE

Damage to the unit if connected

incorrectly. For example, if an electric

load is connected to terminal 4 or if

connected to 2 phases.

Connect the unit as shown in the wiring

diagrams in chapter 12. Do not connect

additional consumers to terminal 4.

DANGER

Danger from electric shock/unit damage

if installed incorrectly with a power

cable that is too long.

If the cable feed is

too long inside the housing, the fan insert

cannot be installed correctly. The power

cable may be damaged when inserting the

fan insert.

Area for mains connection

labelled: Lay wires according to the

contour.

Note that the maximum spacing

to the terminal box is 11 cm. Do not cut the

power cable inside the housing too short.

13

«
...
22
23
24
25
26
...
»

Содержание ER GH

































Отзывы:

Нет отзывов

Похожие инструкции для ER GH

Бренд: S&P Страницы: 24

Бренд: Fandis Страницы: 2

DanX XWPRS 12/24

Бренд: Dantherm Страницы: 36

Бренд: ZALMAN Страницы: 11

Бренд: Faro Barcelona Страницы: 28

Бренд: Vent-Axia Страницы: 16

Бренд: Maxx air Страницы: 10

Smart Fans XF-SCK

Бренд: Modern Forms Страницы: 2

Бренд: Tamarack Technologies Страницы: 4

Бренд: Faro Barcelona Страницы: 13

Бренд: ebm-papst Страницы: 12

Бренд: Saturn Страницы: 10

Бренд: Bigassfans Страницы: 64

Бренд: EUROM Страницы: 52

Ruud G100-200(A)

Бренд: Rheem Страницы: 2

Бренд: Klarstein Страницы: 44

Бренд: ebm-papst Страницы: 14

Бренд: TradeQuip Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды