background image

 

18 (40) 

 

 

Bruksanvisning Geting G1_B_EN 

 

 

Posn. 

Function 

Water on, brushes off 

Off 

Brushes on, water on 

Brushes on, water off 

Lower hopper 

Raise hopper 

Close hopper 

Empty hopper 

3.7  Electrical system 

 

3.7.1 Lighting 

The electrical system is rated for a 12-volt supply. Power is taken from 
the towing vehicle through a cable with 7-pin plug, which is connected to 
the matching socket on the towing vehicle. This supplies the rear lights, 
brake lights, indicators, fog lights and working lights. 

Bulbs 

Location 

Watts 

Fitting 

Rear lights 

10 

15 s 

Brake lights 

21 

15 s 

Indicators 

21 

15 s 

Fog lights 

21 

15 s 

Working lights 

21 

15 s 

3.8  Chassis 

The Geting G1 has a robust chassis made from square tube. The front 
section provides a strong mounting for the tow hitch. It also has a jockey 
wheel that is used when parking the sweeper and makes it easier to hitch 
the sweeper to the towing vehicle. 

One version of the G1 has an overrun brake like that used on trailers. This 
model has a parking brake that should be used when the sweeper is not in 
use. 

Содержание Wasp G1









































Отзывы: